Bedienungsanleitung First Alert FG225 (Seite 2 von 5) (Englisch)

795119

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

HOW TO INSTALL THIS SMOKE ALARM

THE PARTS OF THIS SMOKE ALARM FOLLOW THESE SIMPLE STEPS!

1. “OPEN HERE” tab

2. Cover hinge

3. Test button

4. Power/alarm indicator

Tools you will need:

•Pencil •Drill with 3/16” (5 mm) drill bit

•Hammer • Standard flathead screwdriver

1. Hold base firmly and pull up on cover tab marked “OPEN HERE.”

This will open the hinged cover.The cover may unsnap from the base

if it's opened too far.This will not damage the unit—the cover hinge

snaps back into place easily.

2. Hold the Smoke Alarm base against the ceiling (or wall) and make a

mark at the center of each of the mounting slots with a pencil.

3. Put the unit whereit won’tget covered with dust when you drill the

mounting holes.

4. Using a 3/16” (5 mm) drill bit, drill a hole through each pencil mark.

5. Insert the plastic screw anchors (in the plastic bag with screws) into

the holes. Tap the screw anchors gently with a hammer,if necessary,

until they are flush with the ceiling or wall.

6. Tighten the screws (provided) into the screw anchors, then loosen

them two turns.

7. Fit the Smoke Alarm over the screw heads as shown. Close cover.

8. If the Smoke Alarm cover does not line up the way you want it, rotate

the base and re-tighten the screws.

9. Activate the battery. With the cover open, remove and reinstall the

battery so the terminals on the battery match the terminals on the

Smoke Alarm. Match “+” to “+” and “-” to “-.” Push the battery in

until it snaps in securely and cannot be shaken loose.

If the battery is not snapped in completely, the unit cannot receive

battery power. The Smoke Alarm may beep briefly when you install

the battery—this is normal.

Once the battery is installed, the red power indicator light (behind the

test button) will flash once a minute to show you the Smoke Alarm is

working.

10. Close the cover all the way.

11. Test the Smoke Alarm. See “Weekly Testing.”

Tolock/unlock the cover to the base:

1. Using needle-nose pliers or a utility knife, detach locking

pin from back of alarm base.

2. Insert locking pin into the slot located on the front of the

alarm as shown in the diagram.

3. Remove pin to unlock and replace battery.

Cover Open

1. “Open Here”

2. Test button or Test/Silence

button (FG250 only)

3. Smoke alarm base

4. “No Battery” tab

5. Mounting slots

6. Install 9V battery here

7. Locking pin slot

Locking Pin

Insert Locking Pin

LOCKING FEATURE

This unit is designed to be

mounted on the ceiling, or

on the wall if necessary.

BEFORE YOU INSTALL THIS SMOKE ALARM

IMPORTANT! Read “Recommended Locations for Smoke Alarms”

and “Locations to Avoid for Smoke Alarms” before beginning. This unit

monitors the air, and when smoke reaches its sensing chamber, it alarms.

Itcan give you more time to escape before fire spreads. This unit can

ONLY give an early warning of developing fires if it is installed, maintained

and located where smoke can reach it, and where all residents can hear

it, as described in this manual. This unit will not sense gas, heat, or

flame. It cannot prevent or extinguish fires.

Understand The Different Type of Smoke Alarms

Battery powered or electrical? Different Smoke Alarms provide

different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms

Fire Safety Professionals recommend at least one Smoke Alarm on every

level of your home, in every bedroom, and in every bedroom hallway or

separate sleeping area. See “Recommended Locations For Smoke

Alarms” and “Locations To Avoid For Smoke Alarms” for details.

Know What Smoke Alarms Can and Can’t Do

ASmoke Alarm can help alert you to fire, giving you precious time to

escape. It can only sound an alarm once smoke reaches the sensor.

See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes

This Smoke Alarm is designed to be used in a typical single-family

home. It alone will not meet requirements for boarding houses,

apartment buildings, hotels or motels. See “Special Compliance

Considerations” for details.

• This unit will not alert hearing impaired residents. It is recom-

mended that you install special units which use devices like

flashing strobe lights to alert hearing impaired residents.

•Do not connect this unit to any other alarm or auxiliary device.

It is a single-station unit that cannot be linked to other devices.

Connecting anything else to this unit may prevent it from working

properly.

•Unit will not operate without battery power. The Smoke Alarm

cannot work until you install the battery in the correct position

(Match “+” to “+” and “-” to “-”).

•This Smoke Alarm has a battery guard which prevents it from

closing unless a battery is installed. This warns you the unit will

not operate without a battery.

• Do not install this unit over an electrical junction box. Air currents

around junction boxes can prevent smoke from reaching the

sensing chambers and prevent the unit from alarming. Only AC

powered units are intended for installation over junction boxes.

• Do not stand too close to the unit when the alarm is sounding.

Itis loud to wake you in an emergency. Exposure to the horn at

close range may harm your hearing.

•

Do not paint over the unit. Paint may clog the openings to the

sensing chambers and prevent the unit from operating properly.

First Alert FG225 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info