Bedienungsanleitung First Alert SA67 (Seite 4 von 5) (Englisch)

795113

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

To install this smoke alarm, follow these steps:

This unit is designed to be mounted on the ceiling, or

on the wall if necessary.

Tools you will need:

• Pencil

• Drill with 3/16” (5 mm) drill bit

• Standard/Flathead screwdriver

• Hammer

1. Hold base ﬁrmly and pull up on cover tab

marked “OPEN HERE.” This will open the

hinged cover. The cover may unsnap from the

base if it's opened too far. This will not damage

the unit—the cover hinge snaps back into place

easily.

2. Hold the smoke alarm base against the ceiling

(or wall) and make a mark at the center of each

of the mounting slots with

a pencil.

3. Put the unit where it won’t get covered with dust

when you drill the mounting holes.

4. Using a 3/16” (5 mm) drill bit, drill a hole through

each pencil mark.

5. Insert the plastic screw anchors (in the plastic

bag with screws) into the holes.

Tap the screw anchors gently with a hammer, if

necessary, until they are

ﬂush with the ceiling or wall.

6. Tighten the screws (provided) into the screw

anchors, then loosen them two turns.

7. Fit the smoke alarm over the screw heads as

shown. Close cover.

8. If the smoke alarm cover does not line up the

way you want it, rotate the base and

re-tighten the screws.

9. Activate the battery. With the cover open,

remove and reinstall the battery so the terminals

on the battery match the terminals on the

smoke alarm. Match “+” to “+” and “-” to “-.”

Push the battery in until it snaps in securely and

cannot be shaken loose.

If the battery is not snapped in completely, the

unit cannot receive battery power.

The smoke alarm may beep brieﬂy when you

install the battery—this is normal.

Once the battery is installed, the red power

indicator light (behind the test button) will ﬂash

once a minute to show you the smoke alarm is

working.

10.Close the cover all the way.

11.Test the smoke alarm. Press and hold the test

button on the cover of the unit for 5-20

seconds, or until the alarm sounds (the unit may continue to alarm for a few seconds after you release the

button).

During testing, you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause.

WEEKLY TESTING

It is important to test this unit every week to make sure it is working properly. Using the test button is the

recommended way to test this smoke alarm.

Press and hold the test button on the cover of the unit for

5-20 seconds, or until the alarm sounds (the unit may continue to alarm for a few seconds after you release the button). If

it does not alarm, make sure the unit is receiving power and test it again. If it still does not alarm, replace it immediately.

During testing you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but there are a few simple things

you must do to keep it working properly.

• Test it at least once a week.

• Test units used in RVs after the vehicle has been in storage, before every trip, and once a week while in use.

Failure to test units used in RVs as described may remove your protection.

• Clean the smoke alarm at least once a month; gently vacuum off any dust using your household

vacuum’s soft brush attachment. 1. Open the cover and disconnect the battery. 2. GENTLY vacuum the

inside of the cover and the sensor chamber. 3. Reconnect the battery. 4. Close the smoke alarm, and vac-

uum the outside of the cover. 5. Test the smoke alarm.

Never use water, cleaners or solvents since they

may damage the unit.

• Relocate the unit if it sounds frequent unwanted alarms. See “Where Not To Install Smoke Alarms.”

• When the battery becomes weak, the smoke alarm unit will “chirp” about once a minute (the low battery warn-

ing). This low battery warning should last for 30 days, but you should replace the battery immediately to con-

tinue your protection.

Choosing a replacement battery:

Your smoke alarm requires one standard 9V battery. The following batteries are acceptable as replacements: Eveready

#216, (Energizer) #522, #1222; Duracell #MN1604; Gold Peak #1604P, #1604S; Rayovac 1604, D1604. You may also

use a Lithium battery like the Ultralife U9VL-J for longer service life between battery changes. These batteries are

available at many local retail stores.

IMPORTANT!

Most carbon zinc batteries have an average service life of 1 year; most alkaline batteries have an average service life

of 1-2 years; most Lithium batteries have an average service life of 6-10 years. Actual service life depends on the

smoke alarm and the environment in which it is installed. All the batteries speciﬁed above are acceptable

replacement batteries for this unit. Regardless of the manufacturer’s suggested battery life, you MUST replace the

battery immediately once the unit starts “chirping” (the “low battery warning”).

WARNING!

NEVER use an open ﬂame of any kind to test this unit. You might accidentally damage or set ﬁre to the unit or

to your home. The built-in test switch accurately tests the unit’s operation as required by Underwriters

Laboratories, Inc. (UL). If you choose to use an aerosol smoke product to test the smoke alarm, be certain to

use one that has been Listed to Underwriters Laboratories, Inc. Safety Standards, and use it only as directed.

Use of non-UL Listed products or improper use of UL Listed products may affect the smoke alarm’s sensitivity.

WARNING!

Use only the replacement batteries listed below. The unit may not operate properly with other

batteries. Never use rechargeable batteries since they may not provide a constant charge.

First Alert SA67 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info