Bedienungsanleitung Fiskars Stay Sharp - 6208 (Seite 8 von 19) (Englisch)

714372

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers Fiskars Help Line: 1-877-201-3260 videos & more at: skars.com/reelmowers

Using Your Mower

Are the blades making contact? While your mower’s cutting system was

precision-set during assembly, it is possible that some slippage may occur

during shipping, handling and operation. To check if the cutting gap is set

properly, refer to Checking Cutting Performance on page 11.

Problem: Turning the mower is difficult or requires

stooping.

Is the handle height set properly? If the adjustable handle is set too low,

turning your mower may require you to stoop over. If this happens, refer to

Adjusting Your Mower on page 8 for instructions on raising the handle.

Problem: The mower makes a scraping or

tinging noise.

Is the cutting reel or stationary blade damaged? While your mower has

hardened blades, blade damage can still occur if rocks, concrete edges

or other hard debris are struck. If this happens, the damaged area of the

blade may cause a high-pitched sound when it passes the other blade.

See Care and Maintenance on page 16 for additional details.

Are the blades making contact? While your mower’s cutting system was

precision-set during assembly, it is possible that some slippage may occur

during shipping, handling and operation. To check if the cutting gap is set

properly, refer to Checking Cutting Performance on page 11.

Problem: The mower leaves some uncut blades

of grass.

Is your grass very long or are tall weeds present? If your grass is over 6"

long or tall weeds are present, they may be knocked down by the front of the

mower. If this happens, either pull these long stragglers by hand or make a

second mowing pass to cut them. To prevent this entirely, never let your grass

grow longer than 6".

Does the front of the mower rise off the ground? If the adjustable handle is

set too high, the force you exert when pushing the mower may cause the front

wheels to rise up off the ground, resulting in uneven cutting. If this happens,

refer to Adjusting Your Mower on page 8.

Are the blades set improperly? While your mower’s cutting system was

precision-set during assembly, it is possible that some slippage may occur

during shipping, handling and operation. To check if the cutting system is

set properly, refer to Checking Cutting Performance on page 10.

Problem: The mower is hard to push or the reel

doesn’t spin freely.

Are you trying to cut too much grass? The mower may become hard to

push or even clog if the cut height is set too low for the length of the grass

being cut. If this is the case, readjust the cut height so that you are cutting

no more than 1/3 of the length of the grass.

Is the mower awkward to push? If the adjustable handle is set too high,

it may feel awkward while pushing. If this happens, refer to Adjusting Your

Mower on page 8 for instructions on lowering the handle.

Is the drive train obstructed? If you ﬁnd that your mower becomes harder

to push, examine the ends of the reel and the wheels to see if grass clippings

or other debris have caused a jam. If an obstruction is present, clear it with a

long bristled brush or soft tool.

Troubleshooting

To maximize cutting power, walk briskly. The cutting power of the

InertiaDrive

™

Reel increases with the speed of the mower. This means

that the faster you walk, the better your mower will cut. While it is not

necessary to run, if you’re used to mowing at a very leisurely pace, try

walking just a little more quickly.

For efficient mowing, cut your lawn in long, straight lines. Since

reel mowers only cut grass when they are moving, lay out your mowing

pattern to maximize the amount of long, straight runs and minimize

starts and stops. Overlapping wheel tracks will ensure a complete

and uniform cut.

Precut a turnaround zone to ease turns against obstructions. If any

mowing run ends against an obstruction (garden, foundation, fence,

etc.), begin by making one or two mowing passes along the obstruction

to provide a turnaround zone.

Scotts® Lawns: Your Guide to a Beautiful Yard, Second Edition,

recommends the following cut heights:

Cool Season Grasses

Bluegrasses (2"–4")

Fescue (2"–4")

Ryegrass (2"–4")

Warm Season Grasses

Bermuda (½"–2")

St. Augustine (2"–4")

Zoysia (¾"–2")

Bahia (2"–4")

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fiskars Stay Sharp - 6208 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info