IMPORTANT INFORMATION
Correct usage will ensure to
escape. Every correctly
increase your potential escape time.
•A smoke detector is not a fire-prevention measure.
•Install the smoke detector in the correct place, pos-sible
in the middle of the ceiling.
•Keep the smoke detector out of the reach of children.
•Test the unit on period of
absence.
CAUTION: Never test with fire!
• Clean the detector regularly (once a month) using the soft
brush from a vacuum cleaner. The smoke alarm can also
be cleaned using a moist cloth.
• If the detector emits a beeping sound every 40 seconds,
this means that that
replace the smoke detector.
•The lifespan of smoke detectors is 10 years.
•A false alarm can be silenced by pressing the test and
silence button.
• You can make your Model ASD-10 smoke detector less
sensitive for 8-9 minutes by pressing test but-ton. The
detector sound the
smoke is too significant.
•Plan TWO escape
members of the family.
•IN THE EVENT
IMMEDIATELY
WITH YOU, GATHER OUTSIDE AT
MUSTER POINT AND
PRESENT AND ACCOUNTED FOR.
CLOSE DOORS AND
OPEN A
CHOOSE AN ALTERNATIVE ROUTE. CALL THE FIRE
BRIGADE FROM OUTSIDE OR AT A NEIGHBOUR’S
HOUSE. NEVER BURNING
BUILDING.
• In
the building keeping as close to the floor as possible.
Wherever possible, breathe through a cloth (preferably
moist), or else hold your breath as much as you can. The
majority of deaths and injuries are caused by smoke
inhalation rather than fire itself.
SPECIFICATIONS
Power: 3VDC Lithium AA Battery
Battery life: 10 years under normal
conditions
Usage: < 10 µA continuous
< 60 mA in alarm
Usage temperature: 0ºC to + 55ºC
± 3% at 93% RH at 40ºC
Sensitivity:
Alarm volume:
Certification:
In accordance with EN14604
>85dB at 3 metres
ANPI EN14604, CE-13, BOSEC
POSITIONING THE SMOKE DETECTOR
Minimum protection:
In all rooms, such as bedrooms, living room, study and
suchlike, as well as along escape routes such as corridor
or hallway.
Maximum protection:
- Smoke detector in all rooms (with the exception of
bathrooms, kitchen, garages, etc.)
- Heat detectors can be installed in bathrooms, kit-
chens, airing cupboards, utility rooms, etc. within 5
metres of a potential source of fire.
Recommended
locations:
•The smoke
detector should
preferably be
installed in the
middle of the
ceiling, at least
50 cm from the
wall.
•In the case of
pitched roofs,
install the detec-
landing
tor on the slo-
ping wall, at
least 90 cm (measured vertically) from the ridge of
the roof.
• See minimum and maximum protection (figures 1 & 2)
•Ensure that the detector can always be reached
for testing and cleaning.
Never fit a smoke detector:
• In bathrooms, kitchens, shower rooms, garages, etc.
Places where a may go off needles-
sly to condensation, normal or gases. A
smoke detector should
such sources of smoke.
•Places where the temperature may exceed 50° C
or fall below 0° C, e.g. attics, just above a fireplace,
•In the etc. to) decorative
doors, sockets, lights, fittings, windows, wall venti-
lators, etc. which could mean that smoke does not
reach the smoke detector. Minimum 50cm away.
• Surfaces that are usually warmer or colder than the
rest in
vent smoke from reaching the detector.
•Adjacent to or directly above stoves or heaters.
figure 4
LED-light
test-/pause button
figure 1
kitchen
living room
bath-
room
bedroom
bedroom
bedroom
hallway
bedroom
bedroom
bedroom hallway
kitchen living
room
figure 2
hallway
Instruction manual
10-YEAR OPTICAL SMOKE DETECTOR WITH BUILT-IN 10-YEAR 3V BATTERY
1134
EN14604:2005/AC 2008
Essential characteristics: Performance:
Nominal activation conditions/sensitivity,
response delay (response time) and
performance under fire conditions:
Passed
Fito Products BV
Molenvliet 22
3961 MV
Wijk bij Duurstede
The Netherlands
13
1134-CPR-122
Operational reliability: Passed
Tolerance to supply voltage: Passed
Durability of operational reliability and
response delay, temperature resistance:
Passed
Durability of operational reliability,
vibration resistance:
Passed
Optical smoke
detector, alerts you in
the event of fire or
smoke, and is suitable
for residential
buildings.
Durability of operational reliability,
humidity resistance:
Passed
Durability of operational reliability,
corrosion resistance:
Passed
Durability of operational reliability,
electrical stability:
Passed
FD
9178
RETAIN THESE INSTRUCTIONS FOR USE!
These instructions for use contain important information for correct installation and
use of your smoke detector. Please read this information carefully and retain these
instructions for reference.
Model: ASD-10
•In very high or difficult it hard
to reach the detector to test or clean it.
• In very dusty or dirty places. Accumulati of dust will
prevent smoke from reaching the smoke chamber and in
time will lead to a false alarm.
•Within 1 metre of dimmer switches and wiring. Some
dimmer switches can trigger a fault in the detector.
• Within 1.5 metres of fluorescent lights. Electrical impulses
can adversely affect the functioning of the detector.
• Outdoors and in spaces where a large number of insects
are found.
disrupt the functioning of the detector.
The underside of the detector gives important
information.
ATTENTION: The smoke alarm should be temporarily
removed during renovation work or structural alterati-ons.
Clean
cleaner once the day’s work is complete, and then replace
the detector, always testing it by pressing the test button
once it has been reinstalled.
INSTALLATION
1. Choose a location that
satisfies tions
described in: Positioning
the smoke detector.
2. Remove the base plate
of the
3) by turning
plate (to
the left).
3. Mark the mounting
figure 3
holes in
and drill the holes (use a 6 mm drill). the
screw plugs, then base
plate securely the base
plate is tight circulation
above the smoke alarm is which could impede
smoke detection. If the opening is too large, this should
be remedied using the kit.
4. it
the smoke detector clicks into the base plate. Turn the
smoke detector (to the right from the OFF to the
ON stripe) to
figure 4)
Mounting holes
