Bedienungsanleitung Fito ASD-10 (Seite 2 von 2) (Englisch)

795099

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

PRODUCT WARRANTY

If used and maintained properly, the manufacturer gua-

rantees this product against material and/or manufacturing

faults for a period of 10 years from the original date of pur-

chase by the consumer. Exceptions include damage arising

from accidents or misuse. If the product becomes defective

within the stated period, then it will be repaired or replaced

free of charge. Please do not attempt to repair the product

yourself or tinker with it, which will invalidate the warranty.

MADE IN EUROPE

EUROPEAN SUPPLIER:

Fito Products BV

Molenvliet 22

3961 MV WIJK BIJ DUURSTEDE

The Netherlands

info@fito.nl - www.fito.eu

5. Check that the smoke detector is working and that the

battery has been activated by pressing the test button. A

beeping noise that stops of its own accord indicates that the

smoke detector has been activated and the red LED light will

flash every 10 seconds for 8-9 minutes. Testing the smoke

detector will automatically put it in reduced sensitivity

mode for 8-9 minutes.

• Never allow the detector to come into contact with fluids.

• Clean the detector regularly (once a month) using the soft

brush from a vacuum cleaner. The smoke alarm can also

be cleaned using a moist cloth.

• Repairs must be carried out by the manufacturer.

CAUTION: Never apply paint to the detector and do

not cover it in tape.

Causes of false alarm:

The smoke detector can be activated by steam, condensa-

tion, dust, smoke and small insects. These are to be preven-

ted as far as possible. See section: Never fit a smoke detec-

tor. If a detector is frequently giving a false alarm, it might be

necessary to install the detector in another location.

INSTRUCTIONS FOR REMOVAL

Do not dispose of your old detector in the

bin, but rather hand it in to a local

collection point for small, domestic waste.

LIMITATIONS OF SMOKE DETEC TORS

In countries where they are commonly in use, smoke

detectors have contributed to reducing deaths and injuries.

Independent bodies have established that they were insuf-

ficient in around 35% of fires, namely in the following

situations:

• Where the battery had been removed or was not working.

For that reason, you should test the unit regularly.

• Where smoke is not able to reach the detector in the event

of a fire, meaning the unit cannot be set off. Examples

include a fire on another floor where there is no smoke

detector, a fire behind closed doors, a fire in a chimney or

smoke being blown away from the detector. For that

reason, smoke detectors are recommended in all rooms, or

at any rate on every floor.

• Where the alarm is not heard. A person may not be woken

by the alarm if that person had consumed excess alcohol

and/or drugs.

• A few fires are not always detected on time, e.g. smoking in

bed, if there is no smoke detector in the bedroom. In the

case of escaping from gas or violent explosions,

improperly storing explosive products and flammable liquids

(petrol, paint, methylated spirit, etc.), electrical faults,

acids, children playing with matches (fire).

• The lifespan of smoke detectors is 10 years.

DECLARATION OF PERFORMANCE

You can cownload the Declaration of Performance on our

website www.fito.eu.

2015-04

FUNCTION AND MEANING OF THE LIGHT AND SOUND

SIGNALS:

Normal situation: The red LED light will flash once every 5

minutes.

Alarm: Whenever the detector detects smoke, it will emit a

loud pulsing alarm and the red LED light will flash continu-

ously until the smoke has cleared.

Low battery signal: A beeping signal every 40 seconds

means that the battery is nearly flat and the smoke detector

needs to be replaced. This signal will sound for 30 days.

When properly maintained, as described under IMPORTANT

INFORMATION, the battery and the smoke alarm should

continue to work for over a decade before reaching the end of

their lifespan. You should remove the smoke detector and

base plate from the ceiling and install a new smoke

detector.

Test and Pause Button: Your detector is fitted with a

pause button (see figure 4). This is the same button as the

test button. Press the pause/test button for 2-3 seconds.

Your smoke detector will then go into a so-called reduced

sensitivity mode for 8-9 minutes. The red LED light will flash

every 10 seconds to indicate that the silence button has

been activated. The detector will nonetheless sound the

alarm if the smoke is dense or increasing in quantity. False

Alarm: Press the test button to stop the alarm. (See Test

and Pause button)

Light sensitivity: Three short beeps every 40 seconds, means

the smoke alarm is exposed to too much light

(light spot or sun). Move the smoke detector, or remove the light

source.

Maintenance:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fito ASD-10 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fito ASD-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info