Bedienungsanleitung Flamco Solarix (Seite 6 von 18) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

811830

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

1. General

This manual applies to Flamco Solarix pressure expansion vessels with a capacity of 8 - 80 Litres. The package includes: a

pressure expansion vessel (A) with label (B), a manual (C) and an installation kit (D) if applicable (ﬁ g. 1). See the label for

the maximum working pressure and factory-set pressure. Flamco Solarix pressure expansion vessels are pressure

equipment as deﬁ ned under the European Pressure Directive (97/23/EC). The manufacturer maintains the appropriate

certiﬁ cation.

Use

Flamco Solarix pressure expansion vessels are for use in sealed solar heating systems only (with additives of up to 50%

glycol max.), with a maximum supply temperature of 120 °C. The maximum operating pressure and the maximum

permitted diaphragm temperature are speciﬁ ed on the label. To calculate the capacity and factory-set pressure, please see

the Flamco documentation.

Safety

The pressure expansion vessel comes ready-pressurized. Damage may result in serious injury. The bracket must be able

to take the weight of a full expansion vessel. Protect the unit from excessive pressure. To do this, ﬁ t a safety valve

(e.g. Prescor Solar). Adjust the opening pressure of the safety valve to the maximum permissible operating pressure

speciﬁ ed on the vessel label, or lower. It must NOT be possible to shut off the connection between the pressure expansion

vessel and the solar collector.

2. Fitting

The pressure expansion vessel must be ﬁ tted by approved personnel only.

Local regulations must be observed at all times.

Installation

Pressure expansion vessels with capacities from 8 - 80 Litres must be ﬁ tted with the water nipples (E) pointing upwards

(ﬁ g. 2). If necessary, use wall bracket MB 2 or Flexconsole (up to 25 Litres).

The vessel must be installed as close as possible to the pump on the pressure side. Install the vessel so that the water it

contains cannot circulate.

1. Apply plastic tape (F) (do not use hemp!) to the connection of the expansion vessel. Use plastic tape that is suitable for

the maximum temperature of the liquid used! (Fig. 3)

2. Screw the expansion vessel to the system (T-piece or expansion pipe).

Commissioning

a. Calculate and set the correct pressure (see Flamco documentation).

• Remove the protective cap (G) and valve cap (H) (ﬁ g. 4).

• Measure the pressure.

• If the pressure is too high, allow gas to discharge through the gas valve; if the pressure is too low, ﬁ ll with expansion

gas. Nitrogen must be used as the ﬁ lling gas (ﬁ g. 5).

• Replace the protective cap (G) and valve cap (H) (ﬁ g. 6).

b. Calculate the ﬁ lling pressure (see Flamco documentation).

c. Fit the vessel in the system.

d. Fill the system slowly until the ﬁ lling pressure is reached. Bleed the system during ﬁ lling. Follow the manufacturer’s

instructions at all times!

e. Check the seals for leaks.

f. The expansion vessel is now ready for use.

3. Maintenance and service

It is recommended that the expansion vessel be checked annually by approved personnel.

4. Dismantling

1. Depressurize the system.

2. Remove the protective cap (G) and valve cap (H) (ﬁ g. 7).

3. Push in the inner valve (J) to drain the pressure from the expansion vessel (ﬁ g. 8).

4. Unscrew the expansion vessel (A) (ﬁ g. 9).

Note: a full expansion vessel is heavy!

The water in the expansion vessel may be hot.

Observe local regulations when disposing of the expansion vessel.

GB INSTALLATION AND OPERATING INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flamco Solarix Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info