Bedienungsanleitung Florabest FLB 3000 A1 - IAN 109790 (Seite 10 von 108) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

674626

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

cables with sockets and plugs that com-

ply with the IEC standard 60320-2-3.

Operation

1. Always lead the cable rearwards

away from the device.

2. If a cable is damaged during operation

then disconnect the power supply cable

from the power source immediately.

DO NOT TOUCH THE CABLE BEFORE

YOU HAVE DISCONNECTED IT FROM

THE MAINS.

3. If the connection cable is damaged it

must be replaced by the manufacturer,

a maintenance representative of the

manufacturer or similarly qualified per-

sons in order to exclude possible haz-

ards. If an extension cable is used, then

this must be dimensioned per H05VV-F

(2 x 1.0 mm

) or better.

4. Do not carry the device by the cable.

5. Disconnect the device from the power

supply,

- If you leave the device,

- Before you remove potential block-

ages,

- Before you check, clean or work on

the device,

- If the device starts to produce unu-

sual vibrations.

6. Only operate the device during daylight

or with good artificial lighting.

7. Do not lean too far forward and keep

your balance at all times.

8. Always make sure that you have

stable footing on slopes.

9. Walk, never run.

10. Keep all air intakes free of foreign bod-

ies.

11. Never blow debris towards bystanders.

12. It is recommended that the device is

only operated at reasonable times of

the day - so not early in the morning or

late in the evening - when people could

be disturbed by this.

13. It is recommended to loosen debris with

rakes and brushes first and only then

to start with the blowing or vacuuming.

14. It is recommended that dusty surfaces

be lightly dampened or that a mister is

used.

15. It is recommended to work with the full

blast tube length so that the air flow

can work close to the ground.

Maintenance and storage

1. Ensure that all nuts, bolts and screws

are firmly tightened so that the device is

constantly in a safe working condition.

2. Check the debris bag for wear or dam-

age regularly.

3. Replace parts that are worn out or dam-

aged.

4. Use only original replacement parts

and original accessories.

5. Only store the device in dry locations.

Safe operation

Familiarise yourself with your power

tool. You must have read and under-

stood the operating instructions and

all adhesive labels on your power tool.

Familiarise yourself with the applica-

tions and operational limitations as

well as potential hazard sources of this

power tool.

1. Working area

Untidy work surfaces and working ar-

eas can conceal accident risks. For that

reason workbenches should be kept or-

derly. Floors should be kept clear and

free of waste. Particular care is required

where the flooring is slippery due to

sawdust or floor polish.

2. Working environment

Do not let your power tool come into

contact with rain and do not use it in

damp or wet locations. Ensure there is

always good lighting for the working

area. Do not use the power tool in ar-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Florabest FLB 3000 A1 - IAN 109790 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info