Bedienungsanleitung Fluke 190-062-III (Seite 78 von 98) (Englisch)

775825

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

190 Series III

Users Manual

6. Use one of the ground leads to contact the motor chassis that is the reference ground.

When it is not possible to connect near the shaft, an extension cord with 4 mm connections

on both ends is included for extending the connection to the ground lead. The measurement

can be done on the driven and the non-driven end of the motor.

7. Turn on the motor.

8. Do the measurement after the motor warms up to normal operating temperature.

With this function you can determine the number of flash-overs that occur between shaft and

motor chassis, also referred to as electrical discharge machining. When motor shaft voltages

exceed the bearing grease insulation capability, flash-over currents occur and cause pitting

and grooving of the bearing races.

Tips:

• Under direct 50/60 Hz mains operation, the shaft voltage is normally <1 V.

• Due to the fast edges of the switching voltage from a motor drive, the shaft voltage for a

motor powered by a motor drive can be much higher. High Voltage can cause large

breakdown currents across the grease barrier causing damage to the bearings.

• Normal, unavoidable shaft voltage due to asymmetry in the air-gap magnetic field result in

peak voltages <5 V and slower than 100 ns, which, in general, are not damaging.

• Voltage discharges of >15 V and transition times faster than 50 ns can point to grease flash-

over currents that can damage bearings. However, no fixed values can be given that can be

considered damaging for the motor, as there are many factors that influence this value.

After selecting the Motor Shaft Voltage measurement, the display shows the voltage waveform.

The voltage peak-peak reading shows at the top of the display. Select 2 EVENTS ON to

view the discharge event and count the amount of discharge events. Only the discharge events

show. The readings at the top of the display show the Volt Peak-Peak, dV/dt, and falltime or

risetime as well as the number of events/second. Expect about 20 seconds before the number of

events/second shows on the display.

Use 4 DEFINE EVENTS to define what is considered a discharge event.

In this screen, select the maximum voltage change and maximum rise or fall time that will be

counted and displayed as an event.

Tips:

• No waveform is visible when no events are detected.

• If excessive shaft voltage is measured, check that the voltage discharges can be reduced by

adapting the cabling, grounding, drive parameters, or lubricant. If this is not possible or does

not help, use the shaft grounding devices or the isolated shaft.

• If a bearing runs hot or is noisy and high shaft voltages are measured, bearing flash-over

currents can be the primary source of excessive bearing wear.

• Check other sources of bearing wear, such as, coupling misalignment or looseness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fluke 190-062-III Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info