775826
69
Zoom out
Zoom in
Vorherige Seite
1/98
Nächste Seite
ScopeMeter® Test Tool
MDA-550-III Test Tool
63
When the Motor Drive is on, the waveform does not have a typical sinewave, for example, it
can look more like a camel hump shape. The current readings and waveform shape can vary
as the load changes.
Compare the measured frequency against the specified frequency intended for that circuit.
Nominal frequency (typical 50 Hz or 60 Hz) should be within 0.5 Hz of specification.
Select Harmonics to determine the harmonics related to the waveform shape for both voltage
and current (see Harmonics section).
Voltage Unbalance
Voltage Unbalance checks for the difference between the Phase-Phase voltages for 3-phase
systems.
At the simplest level, all three phases of voltage should always have the same magnitude.
Expressing unbalance as a percentage provides one number to describe the situation. To
calculate the unbalance value:
% unbalance = (maximum deviation from average / average of three phases) x 100 %
While voltage unbalance at motor terminals can adversely affect motor operation, it can also
cause problems at the input side of the drive. As little as 2 % to 3 % voltage unbalance on the
input to a motor drive can cause voltage notching and excessive current to flow in one or more
phases. Voltage unbalance can also cause tripping of the current overload fault protection on the
motor drive.
Tips:
The source of unbalance voltage could be poor installation practices or loads that need to be
correctly optimized. Another common cause of voltage unbalance is single-phase loads
dropping in or out on the same feed as the 3-phase motor drive. To minimize or eliminate this
problem, increase the kVA rating of the transformer or provide a separate feed for the motor
drive.
2 changes the readings that are displayed in the top of the screen to the peak-peak
values of each phase as well as the highest Crest Factor (ratio between peak and rms value)
of one of the phases.
69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fluke 190-102-III wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info