775826
72
Zoom out
Zoom in
Vorherige Seite
1/98
Nächste Seite
190 Series III
Users Manual
66
Motor Drive DC-Bus
The Motor Drive DC-Bus functions check the intermediate circuit of the motor drive.
XW Warning
To prevent possible electrical shock, fire, or personal injury, be aware that the
voltage that is present on the dc bus outputs remains on these outputs after the
motor drive is turned off. The amount of time depends on the internal impedance.
Voltage DC Level
The Voltage DC Level checks the value and stability of the internal DC-bus of the drive and
influence of braking or power feedback (if supported by the drive).
The readings show the dc level, as well as, the peak and peak-peak value. Use Voltage AC
Ripple for a closer look at the ac component.
The dc bus voltage should be about 1.414 times the rms line voltage, except when controlled
rectifiers (IGBT) are used in the input section. A dc voltage that is too low can trip the drive. Low
voltage can be caused by low input mains voltage or distorted input voltage by flat topping.
Tips:
Use the RECORD function to check the dc voltage stability over time and detect slow
fluctuations. The test tool continuously records the digital readings of the measurements and
displays these as a graph.
The TrendPlot graph rolls from right to left like a paper chart recorder. Observe that the
recorded time from start appears at the bottom of the screen. The present reading appears on
top of the screen.
Voltage AC Ripple
The Voltage AC Ripple function detects rapid fluctuations and ac components on the dc-bus.
Tips:
A slight ripple can be visible and is load dependent. If the peaks of ripple have a different
repetitive level, one of the rectifiers could be malfunctioning.
Ripple voltages >40 V can be caused by malfunctioning capacitors or the drive rating is too
small for the connected motor and load.
72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fluke 190-102-III wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info