775826
76
Zoom out
Zoom in
Vorherige Seite
1/98
Nächste Seite
190 Series III
Users Manual
70
Voltage Unbalance
The Voltage Unbalance checks for a difference between the Phase-Phase voltages for 3-phase
systems. The unbalance value is calculated by dividing the maximum rms voltage deviation of
one of the phases and the average rms voltage of all phases.
Voltage unbalance at motor terminals can adversely affect motor operation and can also cause
tripping of the current overload fault protection on the motor drive.
2 changes the readings that show at the top of the screen to the peak-peak values of each
phase as well as the highest Crest Factor (ratio between peak and rms value) of one of the
phases.
Current Unbalance
Current Unbalance checks for a difference between current levels of the phases in 3-phase
systems.
The value is calculated by dividing the maximum rms current deviation of one of the phases and
the average rms current of all phases. Current unbalance should be <6 % and depends on load
current and circuit capacity.
Make sure the phase currents are equal. If one of the phases shows a failure, it can cause the
motor to run hot, not start after stopping, and loose efficiency. A phase failure can be due to
motor drive output malfunction or bad connection between motor drive and motor and can cause
motor overheating.
2 changes the readings that show in the top of the screen to the peak-peak values of each
phase as well as the highest Crest Factor (ratio between peak and rms value) of one of the
phases.
Motor Input
The functions for motor input are identical to motor drive output, except that the phase-dc bus
measurements are left out for voltage modulation, as it is not practical to use the dc bus as
reference on the motor input.
Use the motor input functions to do the same measurements and check the influence of the cable
between the motor drive and the motor and then document the measurements separately in a
report. The voltage modulation measurements are useful to show voltage peaks that are too high
when the cabling is not properly matched.
76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fluke 190-102-III wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info