624064
14
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
10
TS23 PRO Test Set
Users Guide
Originating a Call
1
Press Q.
2
Connect the test leads to the Tip and Ring of a
subscriber loop.
3
Monitor (listen to) the line to verify that it is idle.
4
If the line is not idle, disconnect the test set from
the line.
5
If the line is idle, press P.
6
If there is no data on the line and talk battery is
present, the test set goes off-hook and draws dial
tone.
Note
If there is more than 140 V dc on the line, the
TALK LED is red and test set will not go off-
hook.
7
Dial the desired number.
Note
If you mis-dial the number, press
Q, press
P, then enter the number again.
Disconnecting a Call
To disconnect a call, press
Q or remove the test
leads from the line.
Answering a Call
When the tester receives a ringing signal, press
P to
make the tester go off-hook.
Note
The test set will not go off-hook if the line
voltage exceeds 140 V dc.
Ground Start
Ground start lines are typically found on PBX
installations. To activate an idle, ground-start
telephone line, do the following:
1
Press Q, and connect the test leads to Tip and
Ring of the ground start line. With a third wire,
temporarily short the Tip side of the line to earth
ground. A wire with an alligator clip at each end is
often used for this. Do not allow clips to short
network connections.
2
With the short to earth ground in place, press
P. When dial tone is received, remove the third
wire from earth. The circuit is now ready for
dialing.
Data Safe Practices
With the increase in high capacity data lines in the
distribution system comes the greater risk of disrupting
data services when working on analog lines. Always
monitor the line for an audible signal before
attempting to go off-hook to draw dial tone. To detect
data signals within the human audio range, such as
produced by voiceband modems and subrate DDS
transceivers, you must listen to the line using the test
set’s audio monitoring capability. If you hear the hiss of
a voice band modem or low frequency data transceiver,
do not press
P. If you press P, the test set will go
off-hook and will interfere with the voice band modem
or data transceiver. To avoid this, try another line or
wait until the line is idle.
When going from pair to pair searching for tracer tone
or dial tone, it is best to connect the test set to Tip and
Ring of the pairs. Avoid the practice, either in Talk or
Monitor mode, of clipping one lead of the test set to
ground, and using the other lead to search for tracer
tone or dial tone on a block. This may create an
electrical imbalance on a data line that will disrupt
service. Once you find the voice line you are searching
for then it is OK to test Tip to ground or Ring to ground
on that line.
Be careful not to short the test leads together when
connecting to a data line (or any line for that matter),
as this could bring down the service.
Put the test set in Monitor mode when you use other
instruments to troubleshoot a line.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fluke networks TS23 PRO wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info