Bedienungsanleitung Flyer GOROC X 2022 (Seite 299 von 389) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

803523

299

Zoom out

Zoom in

Vorherige Seite

1/389

Nächste Seite

Asarule,theexibilityis25%ofthetotalsuspen-

sion travel.

In order to adjust the exibility of your suspen-

sionelement,youmustcongurethesuspension

sti󰀨ness/airpressure.Ifyouchangetheairpres-

sure, the overall rigidity of the suspension fork

also changes. The more the suspension element

is pumped up, the harder it becomes. In order to

achieve an optimum balance between the manu-

facturer’srecommendedexibilityandthedesired

rigidity, follow these instructions when adjusting

the suspension element:

Adjustingtheexibility

Ensure that the pressure stages on the fork are

set to the “open” position.

Fill the air chamber, using the table as a guide.

To let air out of the air chamber, remove the air

cap and press the valve pin down or press the air

release button on the suspension pump.

1. Di󰀨erent air pressures or settings

may be necessary. Example: Di󰀨e-

rent driving styles and uses require a

di󰀨erent air pressure and exibility.

Therefore, this adjustment procedure

is just a starting point.

2. The valve cap must always be on the

suspension element while you are riding

so that dirt cannot get into the valve.

Push the O-ring for the suspension path indicator

against the air chamber/the lower fork leg.

Carefully position yourself centrally on the bicyc-

le,thengeto󰀨again.

Important: if you exert too much force on the bicy-

clewhilegettingonando󰀨,youwillobtainimpre-

cise measurements.

Check the position of the O-ring on the housing of

thesuspensionelement.Checkwhethertheexi-

bility is around 25%.

Iftheexibilityislowerthanthevaluerecommended

by the bicycle manufacturer, i.e. the suspension

element is compressed by less than 25%, reduce

the air pressure.

If the exibility is higher than the value recom-

mended by the bicycle manufacturer, increase

the air pressure. Replace the air cap.

Adjustablerebound

The rebound determines the speed at which the

suspension element returns to its fully extended

position after compressing. The suspension ele-

ments have a red rebound dial at the bottom of

the suspension fork that you can use to adjust

the rebound. The suspension element extends

fastest when the adjusting knob is turned

anti-clockwise up to the stop. It rebounds most

slowly when the knob is turned clockwise to the

stop.

Settingtherebound

You can determine the starting point for setting

the rebound at the curb.

Theexibilityofthesuspensionmustbead-

justed before you can adjust the rebound of

the damping.

Perform the test in a safe area with no

tra󰀩c.

Turn the rebound dial anti-clockwise until it reaches

the stop.

Ridethebicycleo󰀨thepavementwhileyouare

sitting on the saddle.

Count the number of times the suspension ele-

ment rebounds.

It should be adjusted so that it rebounds just once.

If it rebounds several times, turn the rebound dial

clockwiseoneclick.Rideo󰀨thepavementagain

and count how many times the suspension ele-

ment rebounds. Repeat this step until the suspen-

sion element rebounds only once.

Note the number of clicks (or turns) through which

you moved the dial from the anti-clockwise stop.

This is your rebound setting.

If the rebound is set correctly for a suspension

fork,thefrontwheel should notlifto󰀨whenthe

fork is compressed when stationary and abruptly

released.Ifthefrontwheelliftso󰀨thegrounddu-

ring this test, turn the rebound through one further

click and repeat the test.

The suspension changes the distance

between the pedal and the ground while

riding.

When riding over bumps, always keep

the crank arms in the horizontal position.

When riding around bends, keep the crank

arms in the vertical position with your foot

down on the outside of the bend in order

to prevent the pedals from touching the

ground.

Suspension and frameset components are

vital parts of your FLYER. Service and

check your FLYER suspension at regular

intervals. Have your FLYER inspected by

your FLYER specialist dealer at regular

intervals.Theframesetwillbemoree󰀨ec-

tive and last longer if it is cleaned on a re-

gular basis. Warm water with a light clea-

ning agent is suitable for cleaning this part

of the bicycle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flyer GOROC X 2022 Seite 299

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info