Bedienungsanleitung Flyer RS serie - Panasonic (Seite 141 von 275) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Norwegisch)

732994

141

Zoom out

Zoom in

Vorherige Seite

1/275

Nächste Seite

139

Loading the battery

The battery can be charged while it is installed in

the e-bike or once it has been removed.

1) Remove the rubber cap

Open the rubber cap on the battery.

Connect the mains plug to a mains socket (220

V - 240 V AC) and connect the charger to the

battery.

Do not connect the charger to the mains

socket immediately after a sudden tem-

perature change from cold to warm. It is

possible that condensed water has col-

lected on the contacts and this will lead

to a short circuit. Do not connect the bat-

tery to the charger immediately after a

sudden temperature change from cold to

warm. Wait until both devices have

reached room temperature before con-

necting the charger or the battery. Al-

ways charge and store the battery and

the charger in a dry and clean environ-

ment.

2) Check the LED charge status indicator

Check whether the charge status LED is lit up.

The LED lights up according to the charge status.

The charge status LED goes off when the charg-

ing process has been completed.

The charging time takes longer if the

battery temperature is too low or too

high.

A fully charged battery cannot be charged any

further.

The battery may not be recharged when

it indicates a fault. The battery might be

damaged after being dropped or due to

mechanical impact, even when there is

no visible external damage. Such batter-

ies must therefore be inspected by a

FLYER specialist retailer. Never try to

open a battery or to repair it.

Protective cap

Charger

3) Remove the plug from the power outlet

Separate the mains plug from the mains socket

after disconnecting the battery from the charger.

It is important that the rubber cap is  rmly reat-

tached before using the battery.

Safety warning regarding the battery charger

The name plate refers to warning notes and other

safety information in connection with handling the

charger. It is important to read them before using

the charger.

Use only the original Panasonic

charger supplied along with your

e-bike. Only this charger is designed for

the lithium-ion battery used on your

e-bike.

Completely charge the battery using the

charger before the  rst ride to ensure full

battery performance. Read and adhere

to the operating instructions for the

charger when loading the battery.

The battery can at any time be charged outside

or installed in the bicycle without reducing its life

span. Interrupting the charging process does not

damage the battery.

The battery is equipped with a temperature moni-

tor that permits charging only within a tempera-

ture range of 0 °C to 40 °C. If the battery temper-

ature is too high, the battery will not charge. In

addition, if you press the control button for the

LED battery charge level, the LED at the very top

[F] and bottom [E] will blink.

Separate the battery from the charger and wait

until it has reached operating temperature. Only

reconnect the charger when it has reached the

permitted operating temperature.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flyer RS serie - Panasonic Seite 141

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Flyer RS serie - Panasonic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info