Bedienungsanleitung Flyer Tour - Panasonic 2018 (Seite 155 von 224) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

780034

155

Zoom out

Zoom in

Vorherige Seite

1/224

Nächste Seite

152 153

You can then remove the

front wheel according to

the steps listed above.

The following applies for rear wheels:

• If your bicycle uses a derailleur gear system,

change gear to the smallest sprocket. In this

position, the rear derailleur poses the least hin-

drance in removing the wheel.

• If your bicycle has quick-release levers or ax-

les, open them.

• If your bicycle has hexagonal bolts, then loos-

en them in anti-clockwise direction with a tting

ring spanner or box-end wrench.

• Pull the rear derailleur backwards somewhat.

• Lift the bicycle slightly.

• Lightly strike the wheel from above with the

palm of the hand.

• Take the wheel out of the frame.

If your bicycle has a gear hub, please consult the

instructions supplied by your manufacturer for re-

moving the wheel.

The valve to your FLYER e-bike’s inner tube

3. Removing the tyre and inner tube

• Unscrew the valve cap, the fastening nut and

possibly the cap nut from the valve.

• Release all of the remaining air from the inner

tube.

• Insert the tyre lever opposite the valve on the

inside of the tyre.

• Insert the second tyre lever approx. 10 cm from

the rst, between the rim and tyre. Lift the tyre

wall over the edge of the rim.

• Repeat this lifting action around the wheel until

the entire tyre is free.

• Remove the inner tube from the tyre.

Schrader valve

4. Change the inner tube

Switch the inner tube for an intact one.

Tubular tires and tubeless tires must be

changed according to the tires and rims’

manufacturer’s instructions.

5. Reassembling the tyre and inner tube

Please avoid allowing foreign bodies in-

side the tyre. Ensure that the inner tube

does not have any folds and is not

squashed.

Ensure that the rim tape covers all spoke

nipples and does not have any damage.

• Place one edge of the rim into the tyre.

• Push one side of the tyre completely into the

rim.

• Insert the valve through the valve hole in the

rim and put the inner tube into the tyre.

• Pull the second side of the tyre into the rim with

the balls of your hands.

• Ensure that the inner tube is correctly posi-

tioned.

• Pump the inner tube up somewhat.

• Check that the tyre is properly in place and

runs true using the control ring on the side of

the tyre. Adjust the positioning of the tyre with

your hand if it does not quite run true.

• Pump the inner tube up to the recommended

tyre pressure.

Please take note of the running direction

of the tyre when installing it.

6. Reattaching the wheel

Reattach the wheel securely back in the frame or

fork with the corresponding quick release, bolted

connection or full oating axle mechanism.

If your bicycle has disc brakes, please

ensure that the brake discs are correctly

secured between the brake pads!

Source: Shimano® techdocs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flyer Tour - Panasonic 2018 Seite 155

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info