Bedienungsanleitung Flyer Urban - Bosch 2016 (Seite 141 von 249) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Norwegisch)

780045

141

Zoom out

Zoom in

Vorherige Seite

1/249

Nächste Seite

139

and then fastened with a screw also exist. Refer

to the attached component manufacturer instruc-

tions and allow your FLYER specialist retailer to

explain the system to you in detail.

Ask your FLYER specialist retailer to ex-

plain in detail how the wheels and all rel-

evant parts are to be correctly and safely

attached using the quick release fastener

or quick release axle system installed.

You will  nd an informative video on the

use of the Suntour® quick release axle on

the Internet at: www.srsuntour-cycling.

com/de/service/tech-videos entitled: “Q-

LOC-2 Assembly Instruction”.

Inappropriately installed wheels may

shift while you are driving or detach from

the vehicle. This may damage the vehi-

cle and lead to severe or life-threatening

injuries to the driver. It is therefore im-

portant to take note of the following in-

structions:

Ensure that the axle, the dropouts and

quick release mechanisms are free of

dirt. Take care that they are correctly at-

tached at all times.

Contact your FLYER specialist retailer

and have your vehicle checked when

you are not sure.

Check that all quick release fasteners

and quick release axles are  rmly at-

tached, even if your FLYER only re-

mained unsupervised for a short time.

You may only start driving when all quick

release fasteners are  rmly closed.

11.2 Setting up the seating position

The seat, handlebars and stem must be adjusted

to your body mass and the desired sitting positon

in order to use your FLYER safely and comfort-

ably.

Only allow FLYER specialists to work on

your handlebars and stem. These are

components which are crucial for your

safety, so incorrect work and tools in this

area of the bicycle could lead to serious

falls.

Quick release lever

Through axle

The seat and stem can be attached with

screw connections or quick releases. Al-

ways secure screw connections with the

correct torque, see Chapter 23.2.

Seat height

In order to transfer the pedal force effectively to

the pedals, you must set your seat to the appro-

priate height.

Find the ideal position by sitting on the FLYER

and placing the heel of your foot onto the pedal in

its lowest position.

Now the bottom leg should be stretched. If this

is not the case, dismount, adjust the seat in the

required direction and try again.

Ensure that the quick release fastener is com-

pletely closed after the adjustment process.

There are markings on the seat post

which show how far it can be pulled out

of the frame. Never pull the seat post be-

yond the maximum length marking. Oth-

erwise the seat post may buckle or

break. If you require a longer seat post

to reach the correct sitting position, talk

to your FLYER specialist retailer. Never

ride with a seat post extended further

than the maximum marker as this could

result in serious falls and injury.

Children and persons who are not con -

dent cyclists should be able to touch the

ground with the tips of both feet. Other-

wise, when stopping they run the risk of

falling and suffering serious injury.

90° arm-upper body angle

min.

7.5 cm

STOP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Flyer Urban - Bosch 2016 Seite 141

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info