Bedienungsanleitung Focus Groove Next - 2018 (Seite 17 von 50) (Englisch)

780051

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

EN-16 Original User Guide | Pedelec Groove Next

1. Undo the seatpost bolt by turning it

anticlockwise with a 4 mm Allen key.

2. Move the seatpost into the right position.

PLEASE NOTE

When lifting the seatpost completely out of the seat tube, be careful

not to damage the light cable. The light cable for the rear light passes

through the seat post into the seat tube.

3. Tighten the seat post bolt again

byturningitclockwisewithatorque

of12-15Nmusingatorquewrench.

4. Test the tightness of the saddle by

trying to move it.

For 1.Loosenseatclamp(s)

For 3.Tightenseatclamp(s)

For 1.Loosenseatclamp(s)

For 3.Tightenseatclamp(s)

3.2 Adjusting the saddle height

Determining the correct saddle height

1. Sit on the Pedelec and at the same time lean against a

wall.

2. Turn the foot pedal on the opposite side to the wall to

its lowest point.

3. Place your heel on the pedal.

Your leg should be fully

extended.

4. If your leg is not fully

extended when your heel is on

the pedal, raise the saddle.

Lower the saddle if you cannot

reach the pedal.

WARNING

Seatpost marking

The seatpost is marked to indicate how far you

may pull it out from the frame. Never pull the

seatpost further out than the marking. This could

cause it to bend or break, and cause you to fall.

For 3. Extend leg

Original User Guide | Pedelec Groove Next EN-17

DANGER

Observe the prescribed tightening torque. Failuretocomplycan

result in screws/bolts becoming loose, tearing away or fracturing. If

that happens while you are riding the bike, components may come

oandyoucouldhaveaseverecrash.Ifscrewsareovertightened,

components can also be damaged.

If no value is shown on the component, use the torque settings from

Chapter  10. Torque settings Page EN-49

3.3 Moving the saddle

DANGER

Screw the clamping screws fully in a straight position in the nuts.

Failuretodosocanresultinthescrewstearingoutofthenuts.

correct

Front seat clamping bolts

wrong

Fig. 1 Fig. 2

1. To move the saddle, loosen the front and rear saddle clamping bolts

(M6)byturningthemanticlockwisewitha5mmAllenkey.Turn

the saddle clamping bolts completely two to three times at most,

otherwise the whole mechanism could fall apart.

2. Movethesaddlebackwardsorforwardsasrequired.

DANGER

Never clamp the saddle in the curve of the saddle rail; always do it in

the straight section. Only shift the saddle within the straight section

(Fig. 1).Saddlesthatstayclampedoutsidethisareacanfail(Fig.2).

correct

Rear seat

clamping bolts

Fig. 1

wrong

Fig. 2

3. Tighten the two saddle clamping

bolts by turning them clockwise

withatorqueof12Nmusinga

torquewrench.

For 3. Tightening the bolts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Focus Groove Next - 2018 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Focus Groove Next - 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info