Bedienungsanleitung Focus SlimFocus (Seite 9 von 28) (Englisch)

810226

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Before commencing Installation, confirm that the details on the appliance

data plate correspond to the local distribution conditions, gas type and

pressure to which the appliance is to be installed.

Ensure that gas supply and supply pipe is capable of delivering the

required volume and pressure of gas and is in accordance with the rules

in force.

GAS CONNECTION

1/2" BSP

VENTILATION

This appliance is a Balanced Flue room sealed appliance, and as such

needs no additional ventilation. However an adequate supply of fresh air to

maintain temperatures and a comfortable environment is recommended.

This appliance may be installed in a completely sealed or mechanically

ventilated house.

APPLIANCE INSTALLATION

Determine the position required for the appliance.

Create a gas connection for the appliance in approximately the correct

location for the gas controls.

The gas controls are connected to the Burner of the appliance.

This appliance must be securely fixed to the floor using the fixings built

into the base of the appliance.

Do not make any adjustments to the appliance.

The appliance and Flue system should be fitted with a minimum clearance

of 500mm from any combustible objects or materials; this includes any

combustible materials used for the fireplace construction.

As this is a room sealed appliance and the appliance stands appropriately

and is securely fixed to the floor, a hearth is not required for this appliance.

A gap of 100mm should be left all round the appliance.

FLUE CONNECTION

A. GENERAL NOTES

This appliance may be installed with a roof terminal (C31) or a wall terminal (C11).

This appliance may only be used with Balanced Flue (otherwise known

as Concentric Flue) parts as specified by Focus. The Focus specified flue

parts have been approved with the appliance. If the appliance is installed

on non-Focus approved parts, Focus cannot guarantee or accept and

responsibility for the proper and safe working of the appliance.

The flue system must be constructed from the appliance upwards, with all

joints being fully locked and sealed using the Focus specified parts.

B. TIMBER FRAME CONSTRUCTION

Whilst it is possible to install room-sealed appliances in timber frame

properties, great care needs to be taken to ensure that the flue assembly

does not interfere with the weather proofing qualities of any outer wall

which it may penetrate. Before attempting this work, further details need

to be referenced, (e.g. “Gas Installations in Timber Frame Buildings” from

the CORGI installer series in the UK).

C. CARPORT OR BUILDING EXTENSION

Where a flue terminal is sited within a carport or building extension, it

should have at least two completely open and unobstructed sides. The

distance between the lowest part of the roof and the top of the terminal

should be at least 600mm.

NOTE: A covered passageway should not be treated as a carport. Flues

should not be sited in a covered passageway between properties.

D. BASEMENTS, LIGHTWELLS AND RETAINING WALLS

Flue terminals should not be sited within the confines of a basement area,

light well or external space formed by a retaining wall, unless steps are

taken to ensure the products of combustion can disperse safely at all

times. It may be possible to install this Balanced Flue system in such a

location provided that it is not sited lower than 1m from the top level of that

area to allow combustion products to disperse safely.

Flue terminals should be sited to ensure total clearance of the combustion

products in accordance with the included information.

When the products of combustion are discharged, they should not cause a

nuisance to adjoining or adjacent properties and they should be positioned

so that damage cannot occur to other parts of the building. If the outer wall

surface is constructed of combustible material, a non-combustible plate

should be fitted behind the terminal projecting 25mm beyond the external

edges of the terminal.

Installation instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Focus SlimFocus Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info