Bedienungsanleitung Focusrite Control 2802 (Seite 6 von 55) (Englisch)

624402

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

6 Control 2802 Operating Manual

Installation

Package Contents

Your packaging should contain the following:

● Control 2802 console

● IEC power cord

● CD containing the documentation and drivers.

Check for any signs of transit damage. If any signs of

mishandling are found please notify the carrier and inform your

dealer immediately.

Important Safety Instructions

Please read all of the safety instructions at the beginning of this

manual before connecting to the mains and powering up the

console. To prevent electrical shock and re hazard, follow all

warnings and instructions marked on the rear of the console.

This unit if connected via its IEC power cord to the mains

safety earth.

NEVER OPERATE THIS CONSOLE WITH THIS EARTH

CONNECTION REMOVED.

Internal Switch Mode Power Supply & Mains

Fuse

The console utilises an internal switch-mode power supply

that is very quiet and passively cooled with plenty of current

capability and headroom. This switch-mode design will accept

any A.C line voltage from 100-240v ±10%. Therefore, the

console will work anywhere in the world provided that your A.C

mains line voltage is within this specication.

Consult a qualied technician if you suspect difculties.

Do NOT attempt to tamper with the power supply or mains

voltages – HAZARDOUS TO HEALTH.

Always replace the mains fuse with the correct value – T2A

slow blow.

Power Up

On power up, please check that the power rail indicators for

+48v d.c and +/-18v d.c light on the top right hand side of the

console:

Service and Repair

The console uses a complex internal PCB sandwich

arrangement making eld service only possible by a qualied

technician.

If any technical issues do arise with your console, please

contact your dealer as soon as possible to arrange for

technical support.

Do NOT attempt to x the console unless qualied to do so.

See the warranty information at the beginning of this manual

for details of your cover.

Dimensions (including rubber feet)

● Height Front: 60 mm

● Height Rear: 170 mm

● Width: 450 mm

● Depth: 550 mm

Ventilation

Care should be taken not to obstruct the series of ventilation

holes in the metalwork of the console. The unit is designed

to release heat and take adequate air ow via these holes to

ensure longevity of performance.

These can be found along the left hand bottom edge on

the side panel (below the cheek), the rear top wrap-around

ventilation panel and below the faders at the foot of the

console.

If mounting the console into some form of studio furniture or

desk, please ensure that there are sufcient air gaps at these

locations:

Lexan Overlay

The front panel at the top of the console (dark section only)

features a rugged under-surface printed polycarbonate overlay.

Exposure to direct sunlight for extended periods of time should

be avoided as this can have a detrimental effect on the overlay

panel and the control knobs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Focusrite Control 2802 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info