Bedienungsanleitung Foscam FI9804P (Seite 9 von 70) (Englisch)

602527

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

www

.foscam.

Foscam Digital Technologies LLC

Telephone: 1-800-930-0949

Access your IP Camera from the Internet

You can access the IP Camera from the Internet (remote access). Enter the WAN IP address and port number

in your standard browser. For example, you would enter http:// 183.37.28.254:85

NOTE:

Make sure port forwarding is successful. You can do port forwarding two ways.

1) Login to your router to enable the “UPNP” function. You can then login to the camera as administrator,

choose Network, and then choose UPnP to enable UPnP. Make sure that the status of UPnP reads “UPnP

Successful” on the Device Status page.

2) Do port (HTTP port ) forwarding manually.

If your router has a Virtual Server, it can do port forwarding. Add the camera’s LAN IP and port which you had

set earlier to your router’s port forwarding settings.

NOTE:

If you plug the camera into a router, it will have a dynamic IP address and you need to set DDNS service

settings to view it remotely.

Step 1: Enter the username and password of the Administrator (default username is admin with a blank

password), and click “OK” to apply changes.

Step 2: Wait around 10 seconds, you’ll see that the camera’s LAN IP address has changed. In our example it

was changed to 2000, so we see http://192.168.8.102:2000 in IP Camera Tool. Also, the LAN IP address is

now fixed at a static IP address of http://192.168.8.102:2000. This IP address will not change even if the

camera is powered off and back on, the camera will remain on this LAN IP address. This is very important that

a static LAN IP address is set, or you may have problems later with remote access and seeing the camera

remotely if the camera loses power and reconnects on a different LAN IP address. Make sure you set a static

LAN IP address!

2.2.2 Dynamic IP Addresses

DDNS is a service that allows your IP Camera, especially when assigned with a dynamic IP address, to have a

fixed host and domain name. This means that even though your WAN IP address is constantly changing, you

will have a fixed hostname you can use to access your cameras at all times. You can access the camera

directly from the Internet using the hostname and port number.

What is the HTTP Port no.?

1) Default HTTP Port is 88

All cameras have the default HTTP port of 88. For example, if the LAN IP link of the camera is

http://192.168.8.102:88, this means that the camera’s HTTP port is 88. You can change port 88 to another port

if you’d like such as 2000 or 8090, which will not be conflict with other existing ports like 25, 21,10000.Here you

can set the port no. between 1 and 65535.

2) Change the default http no.88 to another one.

How to assign a different HTTP Port No. and fixed the LAN IP of the camera by the IP Camera Tool？

Step 1: Open the IP Camera Tool, select the camera you would like to change the port of, right click on the IP

address, and click on ”Network Configuration”, this brings up the network configuration box as shown in Figure

2.4 and 2.5.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Foscam FI9804P Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info