Bedienungsanleitung Frama MATRIX F12 (Seite 33 von 52) (Englisch)

669064

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Frama Matrix F12

5.6. Printer Settings

Information

1. Do not frank mail items thicker than 10 mm. You risk allowing the printing head to touch the

surface of the mail item and thus smearing the franked mark. You should therefore always use

Frama Matrix F12 franking labels for thick letters and packets.

2. Please make sure that no sharp objects, such as paper clips, are near the franking zone. This can

damage the print head.

3. Do not use very absorbent or fibrous envelopes which could prevent a cleanly printed mark. This

could invalidate your franking.

4. The use of coloured envelopes which offer insufficient contrast with the franking mark is not

permitted.

5. After a certain time the printing head is sealed to prevent the individual nozzles from drying. Do

not, therefore, switch the franking system off immediately, but wait until the print head is

sealed, or use the Log off button.

6. Please run a print head test and clean the print head using the Nozzle Cleaning function should

you have the impression that there are lines missing from the franked mark.

7. Always use the functions from the Printer Settings menu. Replacing the print head without

adjusting the alignment and testing from the Printer Settings menu can lead to inadequate

quality of the franking mark.

The Printer Settings menu gives you access to the options and functions required for perfect printing. The

functions in the Printer Settings menu are described in sequence below.

5.6.1. Nozzle test

A franking mark test is incorporated in your Frama Matrix F12

franking system.

This test activates each individual nozzle in the printing head.

This enables you to easily locate defective nozzles, and also to

determine the scope of the cleaning programme.

Press the Nozzle Test key and insert an envelope or

similar into the system.

A test franking mark is made. Check whether all

lines have printed. Run nozzle cleaning if necessary.

5.6.2. Nozzle cleaning

Whi

te lines in the print mark or lines missing from the nozzle test print mean that the print head must be

cleaned to restore the print quality.

Information

Blocked nozzles are often the result of the electric supply being disconnected before the nozzles

could be properly sealed. Always use the system shut-down function to switch off your franking

system reliably.

Two cleaning programmes are available to you for cleaning the nozzles:

Nozzle cleaning: A no

rmal print head cleaning operation is run. The print head and the nozzles are

cleaned.

Nozz

le cleaning +: Intensive flushing and cleaning of the nozzles and the print head.

Press the appropriate key to call up the programme you need. The cleaning programme starts automati-

cally. It is advisable to run the Nozzle Test function afterwards to check how satisfactory the cleaning op-

eration was.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frama MATRIX F12 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Frama MATRIX F12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info