Bedienungsanleitung Franke FIM 1100 W XS (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

510247

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

2) Place the brackets item 7.2 on the wall about 1 or 2 mm from the ceiling or from the upper limit, aligning

its centre on the vertical line. Mark the two eyelet holes of the bracket onto the wall. Drill the holes

for the ﬁxing bracket using an 8 mm masonry bit. Fix the chimney bracket item 7.2 using the screws

item 12a and rawl plugs item 11 supplied.

3) Mark a point on the vertical line at a distance from the cooking appliances of:

d = 1070 mm (Measurement without splashback).

d = height of the splashback (400 mm) + 670 mm (Measurement with splashback item B).

The distance H is the minimum height in mm from the cooking appliances to the bottom edge item L2 of

the front panel of the hood. Draw a horizontal line through the vertical as illustrated in Fig. 1.

Splashback (optional): When a splashback is to be ﬁtted, the distance between the hood and the cook-

ing appliances will be determined by the height of the splashback item B and whether or not there

is a raised back on the worktop. The splashback is to be installed before installing the canopy. If

the splashback is to be ﬁxed to the wall using both the top and bottom ﬁxing holes, Care must be

taken to ensure that the splashback is ﬁtted at the correct height before ﬁxing the base units or at

least the worktop covering them. As this is a complex operation, it should only be undertaken by

the technician installing the kitchen units or by a competent person who knows the ﬁnal dimensions

of the units.

Mark the hole centres for the canopy ﬁxing brackets item 7.1 at item B mm as illustrated in Fig. 1.

Drill the 4 holes for the ﬁxing brackets using an 8 mm masonry bit. Fix the wall brackets item 7.1 using

the screws item 12b and rawl plugs item 11 supplied.

1070

260

7.1

12a

4) Hook the canopy item 1 onto the wall brackets

item 4 as illustrated in Fig. 2. To ensure the cooker

hood is aligned correctly adjust the screws on the top

of the canopy as illustrated

. When the hood is

aligned correctly mark the hole centre on the wall for

the security ﬁxing screw

, which is located in the right

hand bracket on the top of the canopy. Unhook the

canopy from the wall and drill the hole for the security

ﬁxing screw. Hook the canopy onto the wall and ﬁx the

headed screw item 12.a and rawl plug item 11 to

secure the canopy to the wall.

5) Ducting:

The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker

hood is ducted to the outside, charcoal ﬁlters are not required.The ducting used must be 150 mm (6

INS), rigid circular pipe and must be manufactured from ﬁre retardant material, produced to BS.476

or DIN 4102-B1. Wherever possible use rigid circular pipe which has a smooth interior, rather than

the expanding concertina type ducting.

Maximum length of ducting run:

- 4 metres with 1 x 90° bend.

- 3 metres with 2 x 90° bends.

- 2 metres with 3 x 90° bends.

The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components

and ducting kits are optional accessories and have to be ordered, they are not automatically sup-

Fig. 2

plied with the chimney hood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Franke FIM 1100 W XS Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info