Bedienungsanleitung Frico IHS 20 (Seite 6 von 9) (Englisch)

787194

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Infrasmart IP67 - IHSxxx67

Installation and operating instructions

Positioning

The heaters must be placed so that they

cover the area to be heated, see ﬁg. 1. The

normal mounting height is 2–3 metres above

the ground/ﬂoor. A rule of thumb for infrared

heaters is that 600–800 W/m² increases the

experienced temperature by about 10 °C. The

output demand can be reduced if the area to

be heated is protected. If the area only has a

roof, at least 800 W/m² should be installed.

600 W/m² is sufﬁcient if the area has three

walls. For enclosed areas, the output demand

must be calculated. Optimum comfort is

achieved if the heat is distributed from at

least two directions.

Mounting

IHS is installed horizontally on walls with

supplied bracket. For other mounting

alternatives, e.g. in the ceiling, on a ﬂoor

stand, under a parasol or awning, see

accessories. For minimum distances, see

diagrams on introductory pages.

Replacing the lamp

The heat lamp is of the highest quality and

unless it is subjected to mechanical strains in

the form of vibrations and impact it will last

for a long time. The service life is dependent

on the ambient temperature and how the

heater is installed. When the heater is

installed freely and outdoors the temperature

will be low and the life of the lamp longer.

The lamp must be replaced by an installer

or other skilled person.

1. Disconnect the power supply.

2. Wait until the unit is cold.

3. Check that the replacement lamp has the

correct output and voltage.

4. Fit the new lamp. Note do not touch the

lamp with your ﬁngers, wear gloves or the

like.

5. The protective tube must be reﬁtted to the

cables, so that the cables are not damaged

when the grille is ﬁtted.

6. Reassemble the unit again.

General Instructions

Read these instructions carefully before

installation and use. Keep this manual for

future reference.

The product may only be used as set out in

the assembly and operating instructions. The

guarantee is only valid if the product is used

in the manner intended and in accordance

with the instructions.

Application

Infrasmart is a compact, halogen infrared

heater which can be controlled via an app,

remote control (included), or built-in push-

button.

The Frico Infra app is available for both iOS

and Android. It has a range of up to 50 m and

can control up to 8 infrared heaters.

Infrasmart is available in several IP classes

and colours. They are suitable for balconies,

outdoor areas and terraces.

Start-up

When the unit is used for the ﬁrst time or

after a long period of disuse, smoke or odour

may result from dust or dirt that has collected

on the element. This is completely normal

and disappears after a short time.

Connection

IHS is equipped with a 1.9 metre cord with

plug for connection to an earthed outlet

socket. The connection cord must not rest

against the unit as the surface becomes hot or

can be hit by thermal radiation. Contact an

electrician if the cord needs to be changed.

As the halogen lamp has a high starting

current the wall socket should be fuse

protected by a slow burn fuse.

In the event of uncertainty contact an

electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frico IHS 20 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Frico IHS 20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info