Bedienungsanleitung Frico INS (Seite 8 von 11) (Englisch)

787204

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Infraswift

Replacing the lamp and silicon sealing

The heat lamp is of the highest quality and

unless it is subjected to mechanical strains in

the form of vibrations and impact it will last for

a long time. The service life is dependent on

the ambient temperature and how the heater

is installed. When the heater is installed freely

and outdoors the temperature will be low and

the life of the lamp can be expected to be in the

region of 5000 hours.

When replacing the lamp, the silicone sealing

connected to the lamp must also be replaced,

it should be replaced beforehand if there are

signs of aging.

The lamp must be replaced by an installer or

other skilled person.

1. Disconnect the power supply.

2. Wait until the unit is cold.

3. Remove the upper screw that holds the grid

and remove the grid.

4. Remove the side screws (2x) for the wall

bracket and remove the bracket.

5. Remove the upper screw for the reector.

6. Remove the back plastic cover.

7. Remove the screws (4x) for the inner

bottom cover (do not remove screws for the

reector).

8. Detach the lamp together with reector and

inner bottom cover (nuts for the side screws

may fall out).

9. Disconnect white cables (no other cables

should be disconnected).

10. Hold the silicone sealings tight and pull out

the lamp.

11. Replace the silicone sealings to new ones

(make sure that the sealing is properly

assembled).

12. Apply some denatured alcohol on the new

lamp before assembly.

13. Assemble a new lamp in reverse order.

14. Put back the nuts for the wall bracket in

right position before assembly.

15. Reassemble the unit again.

Maintenance

The power supply to the unit must be

disconnected during all service, repair and

maintenance work. Wait until the unit is cold.

The unit has no moving parts so the

maintenance requirement is small, but it must

be kept clean and free from dust and dirt. If

the reector is not clean the thermal radiation

from the unit will decrease and the heater will

become hotter. A large amount of dirt can

cause overheating.

The surface of the reector is sensitive and

must be cleaned with care. If the reector

is dirty it must be cleaned or replaced by a

specialist.

To clean the casing, wipe it with a soft, dry

cloth. If it is very dirty, use a slightly damp

cloth and, if necessary, a mild detergent. Wipe

afterwards with a dry cloth to remove moisture.

Residual current circuit breaker

When the installation is protected by means of

a residual current circuit breaker, which trips

when the appliance is connected, this may be

due to moisture in the heating element. When

an appliance containing a heater element has

not been used for a long period or stored in

a damp environment, moisture can enter the

element.

This should not be seen as a fault, but is

simply rectied by connecting the appliance to

the main supply via a socket without a safety

cut-out so that the moisture can be eliminated

from the element. The drying time can vary

from a few hours to a few days. As a preventive

measure, the unit should occasionally be run

for a short time when it is not being used for

extended periods of time.

Packaging

Packaging materials are chosen with

consideration to the environment and are

therefore recyclable.

Handling of product at end of working

life

This product may contain substances necessary

for the functionality of the product but

potentially dangerous for the environment. The

product should not be disposed of mixed with

general household waste but delivered to a

designated collection point for environmental

recycling. Please contact the local authority

for further details of your nearest designated

collection point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frico INS Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Frico INS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info