Bedienungsanleitung Friedland EvoHome and Garden Kit - D426E (Seite 1 von 1) (Englisch)

608977

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Automatic Programming of bell push transmitter(s)

The first time the chime unit is powered up, the sounds

available are demonstrated. Press the door push until

the chime responds with a tune.

You can leave this tune or change it to the desired tune

by using button A (Fig 7)(see Sound Selection for Tunes)

To program a second push, press the push button until

the chime sounds.

Press the button until the chime sounds, then use button

B to change the tune if required. Programming is now

completed.

If more than 5 minutes has elapsed, you will have to

reset the chime programming by pressing and holding

buttons A and B until the chime

sounds, this takes approximately 5 seconds.

The chime can then be

programmed to 1 or 2 pushes.

200m Chime Sound Variety:

1. Big Ben 2 Note (Default Tune for 1st Push)

2. Mini Bell 4 Note w/ Echo (Default Tune for 2nd Push)

3. Clarinet

4. Altosax

50m Plug-in Chime Sound Variety:

1. Tone Bar 2 Note (Default Tune for 1st Push)

2. Bass clarinet (Default Tune for 2nd Push)

Fig 3

Fig 5

Fig 6

Fig 7

Fig 4

Fig 2

Instructions

– Please retain these instructions for future reference

You will require:

3 x LR6 (AA) alkaline batteries for the Portable Door Chime.

Only long-life alkaline batteries must be used.

A small crosshead and flathead screwdriver, a ø5 masonry drill

Installation

Please note: The stated range of this product is

measured in open field conditions. Walls, ceilings and

the positioning the bell push or door chime on or near

metal structures or reinforced PVC doors or

doorframes will reduce the transmission range.

1. Open the bell push

To open the front cover carefully

insert a flat bladed screw driver,

into the slot and twist gently (A).

When refitting the front cover

to ensure the weather proofing

is maintained, always mount the

bell push in the upright position

and replace the cover securely. (Fig 1)

2. To fit or replace the battery

Open the front cover and insert

the CR 2032 Lithium coin cell

battery into the base as shown

in Fig 2. Any debris created

during installation must be

removed from the base before

fitting battery, to ensure

good contact.

3. Mount the bell push

Ensure the wall surface is clean

and dry. Mount using either the

double sided sticky pad on a

smooth surface, or the screws

and wall plugs provided,

See Fig 3. Do not mount the push

on or near (< 30cm) large metal

objects, as it will block signals from the push.

4. Test the bell push

When the bell push button is

pressed,the confidence light (B)

in Fig 4, will illuminate to reassure

the caller that the bell push is

working.

The light will

flash 5 times when the

battery needs replacing.

5. Fitting or replacing the batteries into the door-chime

Remove battery compartment cover and insert three

LR6 (AA) alkaline batteries as shown in Fig 5.

Refit the battery compartment cover.

6. Use of door-chime

Plug the chime into any

220-240V BS 1363 Socket,

as shown in Fig 6.

installed in a clean dry

environment, situated

within transmission

range of the bell push(es).

200m* Door chime

50m* Plug-in Door chime

8. Sound Selection

A = Main push sound selection

B = Second push sound selection

Chime tune options are as follows:

Declaration

Novar ED&S hereby declares that this Wirefree chime kit is in compliance with

the essential requirements and other relevant provisions of the Radio and

Telecommunications Terminal Equipment ( R & TTE ) directive, 1999/5/EC

Fig 1

Evo Home & Garden Kit

Pack contents:

50m* Plug-in Chime

200m* Portable Chime

Bell push with CR2032 Lithium coin cell battery

Adhesive pad, 2 x screws (ø3x20mm) 2 x wall plugs (ø5x25mm)

for mounting the bell push

Friedland guarantees this product for 3 years from date of purchase.

Proof of purchase is required, this does not affect your statutory rights.

If you require further information about our products, call the Friedland

helpline on 01268 563066.

Friedland a Novar business, Novar ED&S, The Arnold Centre,

Paycocke Road, Basildon, Essex, SS14 3EA, England

www.friedland.co.uk

Trouble Shooting

Chime not Sounding

Batteries may not be inserted correctly

Check all batteries have been inserted correctly

Chime may be positioned out of range of the bell pushMove

your chime closer to the bell push

A metallic object may be blocking the signal from bell push position

Experiment with the location of the chime to see if you can move

it in a more suitable place

The battery in the bell push may need replacing

Press the bell push. If the confidence light (B) flashes 5 times

after being pushed, replace the battery.

Note: In cold conditions, poor location or environment, operating

at maximum range it is advisable to replace the battery more

frequently before the indicator light flashes

(i.e every 12 - 18 months) to maintain optimum performance

Your bell push and chime haven't been programmed

Do the automatic programming of your chime and bell push

The stated transmission range of this product is measured in open field conditions.

Walls ceilings, and metal structures will reduce the maximum range.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Friedland EvoHome and Garden Kit - D426E Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info