Bedienungsanleitung Friedland GlobalGuard Home Alarm System (Seite 9 von 232) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

560834

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

1. Place a first door/window contact detector (zone 1) on the front door.

2. Place a second door/window contact detector (zone 2) on the back door.

3. Place a first PIR movement detector (zone 3) and a second PIR movement detector (zone 4) in two of the following

locations:

- downstairs in the living room containing most valuables

- on the landing covering the access routes between the bedrooms and the stairs

- in the hall covering the control panel and routes between downstairs rooms

5.2 Device range

The quoted range of the system devices is measured in ideal conditions. Any solid object placed between the transmitter and

the receiver will reduce the radio-frequency operating range. The amount by which the wireless range will reduce depends on

the obstruction between the transmitter and the receiver. The effect on the range of multiple walls is cumulative.

Wall type

Range reduction

Dry-lined partition wall

10-30%

Single-layer brick wall

20-40%

Double-layer brick wall

30-70%

Metal panel/radiator

90-100%

5.3 Installation order

1. Installing the solar siren (optional)

Refer to the Installation and Operation Manual. Refer to the Quick Installation Guide.

2. Installing the control panel

Refer to the section “Installing the control panel”.

3. Installing the IP gateway

Refer to the section “Installing the IP gateway”.

4. Installing the PIR movement detector (optional)

Refer to the Quick Installation Guide.

5. Installing the door/window contact detector (optional)

Refer to the Quick Installation Guide.

6. Installing the remote control (optional)

Refer to the Quick Installation Guide.

5.4 Installing the control panel

Note: If you use the solar siren as optional accessory, make sure that the solar siren is installed and its battery is fully charged

before installing the control panel.

1. Keep the control panel out of reach of young children.

2. Mount the control panel to a flat surface at a height between 1.5 and 2 metres. Make sure that the tamper switch is closed

when you mount the control panel to the wall.

3. Locate the control panel in a position out of sight of potential intruders, but easily accessible for system operation and

leaving and entering the house within the set alarm time.

4. Mount the control panel within a protected area so that potential intruder cannot reach the control panel without opening

a door or window protected by door/window contact detector a or passing through an area protected by a PIR movement

detector.

5. Locate the control panel such that the exit/entry tone can be heard from outside the property.

6. Make sure that the distance from the control panel to the wall socket does not exceed the length of the power supply

cable.

7. Make sure that the control panel is installed within effective radio range of the control panel and away from metal objects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Friedland GlobalGuard Home Alarm System Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Friedland GlobalGuard Home Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info