Bedienungsanleitung Friedland HISK1 GlobalGuard Alarm System (Seite 10 von 78) (Englisch)

535711

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

This enables the user to see which user has

Armed/Disarmed the system and if and when

any alarms occurred. The time, date and details

of the event type will be recorded for each

system event.

CHIME

Chime is a low security facility for use when the

system is in Standby mode. If the Chime feature

is ON, and a detector on a zone that has its

Chime function enabled is triggered, the internal

sounder will produce a low volume warning tone.

A typical use of the Chime function would be to

warn that a door or particular area has been

entered.

TAMPER PROTECTION

All security related system devices (except any

Remote Control Units) incorporate Tamper

protection features to protect against

unauthorized attempts to interfere with the

device.

Any attempt to remove the battery cover from

any device (except a Remote Control) or to

remove the Solar Siren or Control Panel from

the wall will trigger the alarm even if the system

is Disarmed (unless the system is in Test or

Program modes).

JAMMING DETECTION

In order to detect any attempts to illegally jam

the radio channel used by your alarm system, a

special jamming detection function is

incorporated into the Control Panel. If this

feature is enabled, an alarm will be triggered if

the radio channel is jammed continuously for

more than 30 seconds or if the system is

jammed for more than 3 periods of 10 seconds

in a 5 minute period. At full alarm it will beep for

3 seconds and will alarm after 10 seconds. At

Part Arm it will beep for 3 seconds.

The jamming detection circuit will constantly

scan for jamming signals. However, it will also

detect and could in extreme cases be triggered

by radio signals from other radio equipment

within range operating on the same frequency

which would not interfere with the normal

operation of your alarm.

If you are planning to operate the Jamming

Detection feature we recommend that you wait

at least 30 days before activating this feature to

allow time for you to become familiar with the

operation of your system.

When activating jamming detection the system

should be monitored carefully for false jamming

alarms for at least 2 weeks before leaving the

Jamming Detection function permanently

enabled.

BATTERY MONITORING

All security devices powered by non-

rechargeable batteries incorporate a battery

level monitoring feature which will warn of a low

battery status.

In addition the Control Panel will also indicate a

low battery status on any PIR (Passive Infra-

Red) movement or Magnetic Door /Window

Detector on the system.

The batteries on any device indicating a low

battery status should be replaced immediately.

HOME AUTOMATION

This system can also accommodate up to 32

wireless receiver home automation devices.

Devices include an ON/OFF Plugin Controller or

Bayonet Lampholder.

These devices are used to simulate the

presence of occupants whilst you are away from

the home.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Friedland HISK1 GlobalGuard Alarm System Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info