535711
19
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
19
The internet connection must be free from
any firewalls/restrictions that might prevent
remote access.
INSTALLING THE IP GATEWAY
1. Connect the IP Gateway to a spare LAN port
on your home broadband router as shown
below:
Connecting gateway to router
2. Connect the 5V DC adaptor and turn on.
3. Check that the power LED on the gateway
turns green which could take up to 1 minute.
LED indications
LINKING AN IP GATEWAY TO THE
CONTROL PANEL (OPTIONAL)
The gateway supplied in this kit has been
supplied pre-linked to the Control Panel at
the factory therefore you do not need to
repeat this. However in the future, should it
ever need to be linked again to the Control
Panel, this can be done as follows:
With the Control Panel in standby mode, enter
programming mode by pressing the following
keys:
,
Use the and buttons to scroll
through the menu until ‘5. Comms’ is displayed.
and press . ‘5-1 Comms Device’ will be
displayed.
Press the enter button again and Input
(01-12) Device NO.’ will be displayed
Using the keypad, enter a device number
between 1 and 12 on the keypad to which you
wish to add the gateway to. If a device is
already linked to this channel then select an
alternative device channel.
Press the enter button and using the
and buttons scroll until ‘:2
Learning ID’ is displayed.
Press the enter button again and
“Waiting Learning..” will be displayed.
Within 30 seconds of entering device learning
mode, press and hold the “Link” button located
on the rear side of the gateway until “Learning
OK” is displayed
User access PIN code
The 4 camera connection LEDs
indicate the status of up to 8
cameras:
1. When connecting 1-4 cameras,
LEDs 1-4 will turn green
2. When the 5
th
camera is added,
LED 1 will turn amber (and so on).
3. If camera 1 is disconnected but
camera 5 is still active, LED 1 will
turn red (and so
on).
RF Connection to Control
Panel LED Green
OK/orange failed
Power /
Connection to
internet LED Green
- ok/Red -failed
IP Gateway
Router
LAN port
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Friedland HISK1 GlobalGuard Alarm System wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info