Bedienungsanleitung Frigidaire FGET3065KF (Seite 3 von 24) (Englisch)

526990

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

(and Optional Electric or Gas Cooktop Combination)

Important Notes to the Installer

1. Read all instructions contained in these installation

instructions before installing the wall oven.

2. Remove all packing material from the oven

compartments before connecting the electrical supply

to the wall oven.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THESE OVENS ARE NOT APPROVED FOR

STACKABLE OR SIDE-BY-SIDE INSTALLATION.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for the

local electrical inspector's use and future reference.

IMPORTANT SAFETY

INSTRUCTIONS

• Be sure your wall oven is installed and grounded

properly by a qualiﬁed installer or service

technician.

•This wall oven must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA

No.70- latest edition in United Sates, or with CSA

Standard C22.1, Canadian Electrical Code, Part 1,

in Canada.

Stepping, leaning or sitting on the

door of this wall oven can result in serious injuries

and can also cause damage to the wall oven.

•Never use your wall oven for warming or heating

the room. Prolonged use of the wall oven without

adequate ventilation can be dangerous.

The electrical power to the oven must

be shut off while line connections are being made.

Failure to do so could result in serious injury or death.

1. Carpentry

Refer to ﬁgure 1 or 2 for the dimensions applicable to

your appliance, and the space necessary to receive the

oven. The oven support surface may be solid plywood or

similar material, however the surface must be level from

side to side and from front to rear.

2. Adjusting Oven Height

Oven height can be adjusted with 2" (5cm) wide wood

shims when needed to ﬁt into an existing cabinet cutout

opening, when cutout height exceeds 28

(71.4cm) for

the single wall oven or 49½"

(125.7cm) for the double

wall oven (see Figure 1 or 2). Place shims of appropriate

height beneath the oven side rails.

3. Electrical Requirements

This appliance must be supplied with the proper voltage

and frequency, and connected to an individual, properly

grounded branch circuit, protected by a circuit breaker

or fuse. To know the circuit breaker or fuse required

by your model, see the serial plate to ﬁnd the wattage

consumption and refer to table A to get the circuit

breaker or fuse amperage.

Table A

Observe all governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or 120/208

Volt, 60 Hz AC only electrical supply is required on a

separate circuit fused on both sides of the line (red

and black wires). A time-delay fuse or circuit breaker is

recommended. DO NOT fuse neutral (white wire). Only

certain cooktop models may be installed over certain

built-in electric oven models. Approved cooktops and

built-in ovens are listed by the MFG ID number (see the

insert sheet included in the literature package).

NOTE: Wire sizes and connections must conform with

the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANSI/NFPA

No. 70-latest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes

and ordinances.

An extension cord should not be used

with this appliance. Such use may result in a ﬁre,

electrical shock, or other personal injury. If you need

a longer power cord you can purchase a 10' (3 m) power

cord kit #903056-9010 by calling the Service Center.

2. These appliances should be connected to the fused

disconnect (or circuit breaker) box through ﬂexible

armored or nonmetallic sheathed cable. The ﬂexible

armored cable extending from the appliance should

be connected directly to the junction box. The

junction box should be located as shown in Figure

1 or Figure 2 and with as much slack as possible

remaining in the cable between the box and the

appliance, so it can be moved if servicing is ever

necessary.

3. A suitable strain relief must be provided to attach

the ﬂexible armored cable to the junction box.

Appliance

Rating Watts

240V

Protection

Circuit

Recommended

Appliance

Rating Watts

208V

Protection

Circuit

Recommended

Less than 4800W

20A

Less than 4100W

20A

4800W - 7200W

30A

4100W - 6200W

30A

7200W - 9600W

40A

6200W - 8300W

40A

9600W and +

50A

8300W and +

50A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frigidaire FGET3065KF Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Frigidaire FGET3065KF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info