Bedienungsanleitung Frigidaire FPGH3077RF (Seite 35 von 36) (Englisch)

590299

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

BEFORE YOU CALL

Oven control panel sounds an

audible alarm and displays an

Error code.

Oven control has detected a fault or error condition. Turn either oven mode or tempera-

ture selector to the OFF position to clear the error code. Try Bake or Broil function. If

the Error code error repeats, turn OFF power to appliance, wait 5 minutes and then

repower appliance. Set clock with correct time of day. Try Bake or Broil function again.

If fault recurs, turn oven mode and temperature selectors OFF and call 1-800-4-MY-

HOME® for assistance.

Soil not completely removed after

Clean

Clean was interrupted. Review instructions in Clean section.

Excessive spills on oven bottom. Clean before starting Clean.

Failure to clean soil from the oven frame, the door liner outside the oven door gasket

and the small area at the front center of the oven bottom. These areas are not in the

self-cleaning area, but get hot enough to burn on residue. Clean these areas before

starting the clean cycle. Burned-on residue can be cleaned with a stiff nylon brush and

water or a nylon scrubber. Be careful not to damage the oven gasket.

Convection fan does not rotate. Oven door is open. Convection fan will turn off if oven door is opened when Convection

is active. Close oven door.

The convection fan will turn on after the oven has been heating for 6 minutes, and

remain on during the cooking process.

Clean does not work. Oven control not set properly. Review instructions in Clean section.

Surface burners do not ignite. Surface control knob was not completely turned to Lite. Push in and turn the surface

control knob to Lite until burner ignites and then turn control knob to desired flame size.

Burner ports are clogged. With the burner OFF, use a small-gauge wire or needle to

burner head slots and ignition ports.

Range power cord is disconnected from outlet (electric ignition models only). Be sure

power cord is securely plugged into the power outlet. Electrical power outage. Burners

may be lit manually. See “Operating the gas surface controls” on page page 9.

Surface burner flame uneven or

only part way around the burner

cap.

Burner slots or ports are clogged. With the surface burner OFF, clean ports with a small

gauge wire or needle.

Moisture is present after cleaning. Lightly fan the flame and allow burner to operate

until flame is full.

Burner caps are not seated properly. Check that all burner caps are level and seated

correctly on burner heads.

Surface burner flame is too high. Surface control knob is set too high. Adjust to lower flame setting.

Burner caps are not seated properly. Check that all surface burner caps are level and

seated correctly on surface burner heads.

Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Frigidaire FPGH3077RF Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info