Bedienungsanleitung Fuji Bike (Seite 57 von 67) (Englisch)

540674

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

NOTE: Installing more than 40mm (1.5”) stack height of headset spacers can compromise the strength of the steerer tube.

(See fig. 2)

It is recommended that the initial installation of the fork be done with the maximum allowed stack height (40mm) of headset

spacers, unless the desired stem height is pre-determined. Place the spacers above or below the stem to adjust your position.

Once a precise stem

height is achieved, a cut can be made to eliminate any spacers that are above the stem.

3. CUTTING THE FORK STEERER TUBE

Make a mark on the steerer tube at the top of the stem once the desired stem height is achieved. The actual cutting line

must be 2mm below the mark. (See fig. 2)

Before cutting the steerer tube, wrap the area where you intend to cut with several layers of masking tape or duct tape.

This will limit the amount of fraying of fibers, resulting in a cleaner cut. Once wrapped, determine the exact location of the

desired cut by a pen mark on the

tape.

NOTE: It is recommended that a fine tooth (36 teeth) saw blade be used to avoid the fraying

of composite fibers. A

carbide grit toothless saw blade is also acceptable.

Please abide by the adage: “check twice, cut once!” It’s much easier than buying a new fork. NOTE: Fuji recommends that

when cutting a steerer tube, a steerer tube cutting guide tool be used. It is very important that the steerer tube be cut straight.

Once the steerer tube is cut, round out the top edge of the steerer tube by using an emery board or fine grit sandpaper.

Wipe off excess dust. DO NOT breathe carbon dust!

4. FORK INSTALLATION

Install the steerer tube plug. Insert the fork back into the headset and place the desired amount of headset spacers to

achieve proper stem height. When proper height is achieved, install the preload cap.

NOTE: Do not twist stem onto carbon steerer tube. This could result in damage to the steerer tube and render the fork

unsafe.

Adjust the headset to eliminate any free play, make sure that the fork still rotates freely. Make sure that the stem and fork are

aligned. Tighten the stem’s top and bottom steerer clamp bolts in an alternating pattern. Increase torque in 5 in-lbf (0.56 N-m)

increments, until the specified torque is achieved. Recommended torque for the steerer tube is 75in-lbf

(8.5N-m). Do not

exceed maximum torque of 90 in-lbf (10.1 N-m).

Install the front brake on the fork. Recommended torque is 70 in-lbf (8 N-m). Do not exceed maximum torque of 87

in-lbf (10 N-m).

Warning: It may be visually difficult to identify damage to the composite material. If the external composite

urface is dented, frayed, gouged, deeply scratched, fractured,chipped or otherwise damaged, the component

should be replaced. If seat post has been involved in a crash or impact, even if there is no visible damage, Fuji

or an authorizedFuji dealer should inspect the product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fuji Bike Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info