Bedienungsanleitung Fujifilm Finepix F710 (Seite 12 von 65) (Englisch)

101549

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

Using the Camera

Use the LCD monitor to frame the shot so that the

subject fills the entire AF (Autofocus) frame.

●

The image on the LCD monitor before the picture is taken

may differ in brightness, color, etc. from the image actually

recorded. Play back the recorded image to check it (➡P.29).

●

The subject may sometimes be difficult to see clearly on the

LCD monitor (in bright sunlight or dimly lit scenes, etc.). If so,

use the viewfinder to take the picture.

To take the picture, press the Shutter button down

fully without lifting your finger off. The camera clicks

and takes the picture. The data is then recorded.

●

There is a slight delay between the Shutter button being

pressed and the picture being taken. Playback the shot to

check the image.

●

When pressing the Shutter button down fully in one motion,

the camera takes the shot without the AF frame changing.

●

When the camera takes the picture, the viewfinder lamp lights

orange (shooting disabled). The viewfinder lamp then turns

green and the next picture can be taken.

●

The viewfinder lamp blinks orange while the flash is charging.

The LCD monitor may go dark briefly. This is normal.

●

See P.118, 119 for information on the warning displays.

Click

AUTOAUTO

１９１９

Bebeep

Press the Shutter button down halfway. The

camera emits a short double-beep and focuses on

your subject. The AF frame on the LCD monitor

becomes smaller and the camera sets the shutter

speed and aperture (the viewfinder lamp (green)

stops blinking and remains lit).

●

If the camera does not emit a short double-beep and “{”

appears on the LCD monitor, the camera cannot focus.

●

Pressing the Shutter button down halfway freezes the image

on the LCD monitor briefly. This is not the recorded image.

●

If “{” appears on the LCD monitor (e.g. the shot is too dark

for the camera to focus), stand about 2 m (6.6 ft.) from your

subject to take the picture.

When the flash will fire, “¨” appears on the LCD

monitor.

Ｆ５．６Ｆ５．６

２５０２５０

◆

Subjects not suitable for autofocus

◆

The FinePix F710 uses a high-precision autofocusing mechanism. However, it may have AF frame

difficulty focusing on the following:

h Very shiny subjects such as a mirror or car body

h Subjects photographed through glass

h Subjects that do not reflect well, such as hair or fur

h Subjects with no substance, such as smoke or flames

h Dark subjects

h Fast moving subjects

h Subjects with little or no contrast between the subject

and the background (such as white walls or subjects

dressed in the same color as the background)

h Shots where another high-contrast object (not the

subject) is close to the AF frame and is either closer or

further away than your subject (such as a shot of

someone against a background with strongly

contrasting elements)

For such subjects use AF/AE lock (➡P.26).

1Set the Power switch to “q”.

2Set the Mode dial to “B”.

h Focal range

Approx. 60 cm (2.0 ft.) to infinity

●

Use Macro mode for subjects closer than 60 cm (2.0 ft.)

(➡P.43).

●

If “å”, “©”, “∆” or

“˙” appears, see P.118.

Press the Flash pop-up button to pop up the flash.

●

When the flash pops up, the image on the LCD monitor may

disappear and the LCD monitor may go dark due to flash

charging. When this happens, the viewfinder lamp blinks

orange.

●

If the flash is used in very dusty conditions of when it is

snowing, white dots may appear in the image due to flash

reflecting off dust particles or snowflakes. Use Suppressed

flash mode.

●

When the camera is turned off, the flash is closed.

Brace your elbows against your sides and hold the

camera with both hands. Position your right thumb

so that it is handy for using the zoom.

●

Moving the camera while shooting gives a blurred picture

(camera shake). Use a tripod to avoid camera shake,

particularly for shots in the dark when the selected flash

mode is Suppressed flash.

●

There may be some unevenness in the brightness at the

lower edge of the LCD monitor. This is normal and does not

affect the image.

01 02

●

Check that the lens is clean. If it is dirty, clean the lens as

described on P.115.

Hold the camera so that your fingers or the strap do

not cover the lens, flash, AF-Assist illuminator or

Flash control sensor. If the lens, flash, AF-Assist

illuminator or Flash control sensor is obscured, the

brightness (exposure) of your shot may be

incorrect.

To zoom in on the subject, press “T” (Tele zoom)

button. To zoom out, press “W” (Wide zoom)

button. A “zoom bar” appears on the LCD monitor.

h Optical zoom focal length

(35 mm camera equivalent)

STD: Approx. 32.5 mm-130 mm

WIDE: Approx. 35.5 mm-142 mm

Max. zoom scale: 4×

●

Zooming stops briefly when the camera changes between

optical zoom and digital zoom (➡P.27). Press the same

Zoom button again to change zoom modes.

AUTOAUTO

Zoom bar

１９１９

TAKING PICTURES

(

B AUTO MODE

)

STILL PHOTOGRAPHY MODE

AF frame

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujifilm Finepix F710 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info