Bedienungsanleitung Fujifilm Finepix S9100 (Seite 37 von 83) (Englisch)

41373

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

72 73

Advanced Features

MODE SELECT

ISO

AUTO

External flash settings (for flashes

with automatic flash control)

For external flash, refer to the user’s manual for the

flash and specify the settings as described below.

h Select external flash mode (TTL mode cannot be

used).

h Match the settings to the camera aperture setting.

Set the flash for the aperture setting measured by

the camera.

h Match the sensitivity setting (➡ P.61) to the

setting on the camera.

●

After taking the picture, check the color (white balance)

setting for the image.

i Set “IMAGE DISP.” to “1.5 SEC”, “3 SEC” or “CONT” in the

SET-UP menu (➡P.101).

i Set the Power switch to “

w” (➡P.31).

Click

Hold a sheet of white paper so that it fills the entire

screen.

When pressing the shutter button, the flash fires

and the white balance is set.

When the white balance is incorrect

Adjust the white balance to match the external flash.

In “»” WHITE BALANCE in the photography menu

(➡P.66), select “O, P” custom white balance.

Press the “MENU/OK” button.

CUSTOMCU STO M

AUTOAU TO

SETSE T

AUTOA U T O

OFFOFF

When [OVER] or [UNDER] appears, the white

balance was not measured at the correct exposure.

Set the exposure compensation again, using a

negative value (–) when [OVER] appears and a

positive value (+) when [UNDER] appears.

OVEROV ER

ISO

200

IS O

200

ISO

200

NNN

OVEROV ER UNDERU NDER

PHOTOGRAPHY MENU

✽ Displaying the menus (➡P.63)

Select “ON” in this setting when using an external

flash unit. Synchronized shutter speeds up to

1/1000 sec. can be used.

●

The image may appear dark when the shutter speed is set to

speeds higher than 1/1000 sec.

●

Set the white balance (➡P.66) to “AUTO” or custom white

balance (➡P.73).

EXTERNAL FLASHEXT ERNA L FL ASH

EVE V

OFFOFF

ONON

STDSTD

Hot shoe

1Close the built-in flash.

2Mount the external flash on the camera’s hot

shoe and tighten the locking screw.

●

If you pop up the built-in flash when the external flash is set

to “ON”, the built-in flash fires once as a signal for the

external flash to fire. The hot shoe and the Synchronizing

terminal do not make a signal for flash.

Ordinary external flash units can be used.

However, some camera-specific flash units cannot

be used.

USING AN EXTERNAL FLASH

Available Photography modes: N, M, <, >

◆

Using a Synchronizing terminal

◆

Attach the synchronization cord from the external

flash to the Synchronizing terminal on the camera by

pushing the cord into the terminal securely.

Synchronization

cord

Synchronizing terminal

Synchronizing

terminal cap

◆

Compatible Flash Units

◆

Flash units that can be used with this camera must meet the following 3 conditions:

hThe aperture can be set.

hExternal flash synchronization can be used.

hThe sensitivity can be set.

The mode can be set to “N”, “M”, “<” (➡P.41, 42,

43) or “>” (➡P.44), but the use of “<” or “>” is

better.

●

Flash photography cannot be used when Top 4-frame

continuous shooting (➡P.54) or auto bracketing (➡P.54) is

selected.

✽ Illustration is display of the external flash

(commercial available).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujifilm Finepix S9100 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fujifilm Finepix S9100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info