617526
34
Zoom out
Zoom in
Vorherige Seite
1/41
Nächste Seite
Troubleshooting
Troubleshooting
Should an error occur, rst che ck the following points. If the distortion is s till not eliminated,
the monitor should, if possible, be c hecked on ano ther computer.
If you canno t solve the problem, please contact our Service Desk.
Having this problem? Check the following point s:
No screen display
Power indicator do es not light up
Check whethe r the ON/OFF sw itch on the
monitor is switched on.
Check whether the power c
able on the
monitor is connected co
rrectly.
Check whether the compute r is switched on.
No screen display
Power indicator is lit
Check whether the compute r is switched on.
Check whe ther th e data c able for the
monitor is corre ctly attached to the monitor
port on the computer.
Press any key on the compute r keyboard.
The computer may be in power saving
mode.
Alter the brightness and/or contrast until you
get a picture.
Message: No Signal
Check whe ther th e data c able for the
monitor is corre ctly attached to the monitor
port on the computer.
Check whether the compute r is switched on.
Message:
Frequency out of range: ## kHz / ## Hz
Please change the display mode to 1680
x 1050 with 60 Hz (B22W-6 LED)
or
Frequency out of range: ## kHz / ## Hz
Please change the display mode to 1280
x 1024 with 60 Hz (B19-6 LED)
The input signal (horizontal frequency a nd
refresh rate) at the displayed input does not
correspond to the technical data for the monitor.
Adjust the video frequency range using the
computer software (see documentation for
the computer or display adapter).
Set a diff
erent screen resolution using the
computer
software (see d ocumentation for
the comp
uter or display adapter).
Picture
position not correct
The monitor recognises an undened mode (see
chapter "
Technical specication", Page 33).
Press the
AUTO
button to con duct the
auto-adjustment of the screen.
Picture is shaking
Check whe ther th e data c able for the
monitor is corre ctly attached to the monitor
port on the computer.
Press the
AUTO
button to con duct the
auto-adjustment of the screen.
Picture is wrongly adjusted Press the
MENU
button to activate the
Factory Recall fu nction.
The Auto Processing message appears.
30 Fujitsu Tech nolo gy Solutions
34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

fujitsu-b19-6-led

Suche zurücksetzen

  • Wie aktiviere ich die Tonwiedergabe auf dem Fujitsu-Monitor B19-6LED44? Eingereicht am 7-2-2021 16:42

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fujitsu B19-6 LED wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Fujitsu B19-6 LED

Fujitsu B19-6 LED Bedienungsanleitung - Deutsch - 42 seiten

Fujitsu B19-6 LED Bedienungsanleitung - Holländisch - 42 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info