617602
36
Zoom out
Zoom in
Vorherige Seite
1/43
Nächste Seite
Troubleshooting
Troubleshooting
Should an error occur, rst check the following points. If the distortion is s till not eliminated,
the monitor should, if possible, be checked on another compute r.
If you cannot solve the problem, please contact our Service Desk.
Having this problem? Check the follo wing points:
No screen display
Power indicator does not light up
Check whether the power cable on the
monitor is connected correctly.
Check whether the comput
er is switched on.
No screen display
Power indicator is lit
Check whether the compute r is switched o n.
Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
Press any key on the compute r keyboard.
The compute r may be in p ower saving
mode.
Alter the brightness and/or contrast until you
get a picture.
Message: No Signal
Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
Check whether the compute r is switched o n.
Message:
Frequency out of range:
##kHz/##Hz
Please change the display mode
to 1920 x 1080 with 60 Hz
The input sign
al (horizontal frequency and
refresh rate
) at the displayed input does not
correspond t
o the technical data f or the monitor.
Adjust the v
ideo frequency range using the
computer so
ftware (see documentation for
the compu te
r or display a dapter).
Set a different screen resolution using the
computer software (see documentation for
the computer or display a dapter).
Picture position not correct
The monitor recognises an undened mode (see
chapter "
Technical specication", Page 35).
Press the
AUTO
button to conduct the
auto-adjustment of the screen.
Picture is shaking
Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
Press the
AUTO
button to conduct the
auto-adjustment of the screen.
Picture is wro ngly adjusted
Run
the Factory Recall function in the OSD
men
u.
The Auto Processing message appears.
Picture disturbances (vertical line s)
Press the
AUTO
button to conduct the
auto-adjustment of the screen.
32 Fujitsu
36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fujitsu B23T-7 LED wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Fujitsu B23T-7 LED

Fujitsu B23T-7 LED Bedienungsanleitung - Deutsch - 43 seiten

Fujitsu B23T-7 LED Bedienungsanleitung - Holländisch - 43 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info