617314
54
Zoom out
Zoom in
Vorherige Seite
1/74
Nächste Seite
Removing and installing components
during servicing
Preparing to remove components
If you are going to remove or ch ange syst e m components, p repare for the removal as follows:
Please observe the safety information in chapter "Importa nt notes", Page 6.
Remove the power plug from the mains o utlet !
Switch the device off.
The device must not be in energy-saving mode !
Close the LCD screen.
Remove all the cables from the device.
Turn the device over and place it on a stable, at and clean surface. If necessary, lay an
anti-slip cloth on this surface to prevent the device from being scratched.
Remove the battery (see "
Removing a battery", Page 25).
Installing and removing memory expansion
MemorymoduleMainmemoryRemovingmemorySystemexpansionSystemexpan sion
If you are asked by the Hotline/Help Desk to remove and install the memory
expansion module yourself, proceed as follows:
Please observe the safety information in chapter "Importa nt notes", Page 6.
The notebook mu st be switched off when installing/removing memory modules
and it must not be in one of the power saving modes.
Only use memory expansion modules that have been a pproved f or your
notebook (see "
Technical data", Page 59).
Never use force w hen installing or removing a memory extension.
Make sure that foreign obje cts do not fall into the memory extension c ompartment.
The memory m odule is located unde
rneath the s ervice compartment. You must open the service
compartment to remove or install
a memory module. Once you have remo ved the cover,
the various components are expo
sed. These components should b e removed and replaced
only by authorised specialist
s. Therefore, be sure to observe the following:
Individual compo nents (e.g.
the processor heat sink) can become very hot
during operation. Therefore
, we recommend that you wait one hour after
switching off the notebook b
efore removing or installing memory modules.
Otherwise, there is a risk of
suffering burns!
As some components are expos
ed that are sensitive to static electricity, please take
note of chapt er "
Notes on ins
talling and removing boards and components", Page 43.
44 A26391-K214-Z200-1-7619, edition 1
54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fujitsu LIFEBOOK A1130 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Fujitsu LIFEBOOK A1130

Fujitsu LIFEBOOK A1130 Bedienungsanleitung - Deutsch - 77 seiten

Fujitsu LIFEBOOK A1130 Bedienungsanleitung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info