Bedienungsanleitung Fujitsu LifeBook E8010 (Seite 69 von 124) (Englisch)

574840

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Troubleshooting

The batteries seem to

discharge too quickly.

(continued

The batteries have been

exposed to high temperatures.

Replace the batteries.

The batteries are too hot

or too cold.

Restore the notebook to normal operating tempera-

ture. The Charging icon on the Status Indicator

panel will flash when the battery is outside its

operating range.

Shutdown and Startup Problems

The Suspend/Resume

button does not work.

The Suspend/Resume button

is disabled from the Advanced

submenu of the Power menu

of the setup utility.

Enable the button from the setup utility.

You did not hold the button

in long enough.

Hold the button longer. This may need to be a few

seconds if your application is preventing the CPU

from checking for button pushes.

There may be a conflict with

the application software.

Close all applications and try the button again.

The system powers up, and

displays power on informa-

tion, but fails to load the

operating system.

The boot sequence settings

of the setup utility are not

compatible with your

configuration.

Set the operating source by pressing the [ESC] key

while the Fujitsu logo is on screen or use the [F2]

key and enter the setup utility and adjust the source

settings from the Boot menu. (See BIOS Setup

Utility on page 29 for more information)

You have a secured system

requiring a password to load

your operating system.

Make sure you have the right password. Enter the

setup utility and verify the Security settings and

modify them as accordingly. (See BIOS Setup Utility

on page 29 for more information)

Internal hard drive was

not detected.

Use the BIOS setup utility or Primary Master

submenu, located within the Main menu, to try to

auto detect the internal hard drive.

An error message is

displayed on the screen

during the notebook

(boot) sequence.

Power On Self Test (POST) has

detected a problem.

See the Power On Self Test (POST) messages to

determine the meaning and severity of the problem.

Not all messages are errors; some are simply status

indicators. (See Power On Self Test Messages on

page 64 for more information)

Your notebook appears to

change setup parameters

when you start it.

BIOS setup changes were not

saved when you made them

and exited the BIOS setup

utility returning it to

previous settings.

Make sure you select Save Changes And Exit when

exiting the BIOS setup utility.

The BIOS CMOS hold-up

battery has failed.

Contact your support representative for repairs.

This is not a user serviceable part but has a normal

life of 3 to 5 years.

Your system display won’t

turn on when the system is

turned on or when the

system has resumed.

The system may be password-

protected.

Check the status indicator panel to verify that the

Security icon is blinking. If it is blinking, enter your

password.

Problem Possible Cause Possible Solutions

E Series.book Page 61 Friday, May 14, 2004 1:25 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujitsu LifeBook E8010 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info