Bedienungsanleitung Fujitsu-siemens fi-7160 (Seite 105 von 229) (Englisch)

560211

105

Zoom out

Zoom in

Vorherige Seite

1/229

Nächste Seite

Chapter 5 Various Ways to Scan

Appendix

Glossary

Introduction

Index

Contents

TOP

105

How to Load

Documents

Daily Care

Troubleshooting

Operational

Settings

Replacing the

Consumables

Scanner

Overview

Various Ways to

Scan

Configuring the

Scan Settings

How to Use the

Operator Panel

2 If you open the ADF to remove the document, close it.

For details, refer to "1.4 Opening/Closing the ADF" (page 27).

3 Load the documents back in the ADF paper chute

(feeder).

If a multifeed by difference in length is detected, either press the

[Scan/Enter] button or perform a scan from the computer (do not

press the [Menu] button).

If there is an attachment which is likely to be the cause of the

multifeed error, then proceed to the next step.

4 Press the [Menu] button and confirm that the LCD displays [Do

not detect] or [Remember], and then either press the [Scan/

Enter] button or perform a scan from the computer.

From this point, note that the indication on the LCD switches between

[Detect][Do not detect] or [Remember][Do not remember] every

time you press the [Menu] button. When [Do not detect] or

[Remember] is displayed, the scanner operates in each mode as

follows:

z Manual mode (Bypass by front panel button)

Scans the next sheet without multifeed detection, and from the

second sheet, multifeeds are detected based on the setting

configured in the scanner driver or the Software Operation Panel.

z Auto mode 1 (Bypass by combination of length and position)

Memorizes the length and location of the paper attachment that

was detected as multifeed, and continues scanning. When a paper

attachment of a similar pattern is detected, multifeed detection is

automatically suppressed.(*1)(*2)

z Auto mode 2 (Bypass by length)

Memorizes the length of the longest paper attachment that was

detected as multifeed, and continues scanning. When a paper

attachment of the same length or shorter is detected, multifeed

detection is automatically suppressed.(*1)(*2)

*1: 8 overlap patterns can be memorized in this mode. When it

exceeds this limit, the first pattern that was memorized is

erased from the memory.

*2: To erase the memorized overlap patterns and the longest

overlap length, use [10: iMFF Setting] on the [Settings Menu]

screen of the operator panel, or Software Operation Panel.

After erasing is completed, the indication on the LCD changes

to or . This allows you to erase multifeed

patterns and the longest overlap length that were not

supposed to be memorized. Be careful with this operation

because all memorized patterns will be erased.

Be careful not to have your fingers caught

when closing the ADF.

ATTENTION

Confirm that the ADF is closed properly. Otherwise, the document

may not be fed into the ADF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fujitsu-siemens fi-7160 Seite 105

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info