Bedienungsanleitung Furuno 1761MK3 (Seite 22 von 33) (Englisch)

596237

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

2-11

1. Determine the guard zone (usually 360

degrees) with the guard alarm function.

2. Press the [MENU] key to open the menu.

3. Operate the trackball to select “7.

WATCHMAN” .

4. Press the [RANGE] key to select a trans-

mission interval.

5. Press the [MENU] key to actuate the

watchman mode. The indication “WATCH-

MAN” appears and the radar transmits for

one minute and then turns to stand-by,

and “ECHONOMY” lights.

Note: The antenna radiator does not rotate

in the “ECHONOMY” (stand-by) mode. How-

ever, the radiator rotates continuously dur-

ing the watchman mode.

6. The radar automatically starts transmit-

ting after the time selected at step 4 has

passed. It transmits for one minute ap-

proximately and examines the guard zone

for change.

(a) If the condition is unchanged, the ra-

dar automatically returns to stand-by

again and continues operating in the

watchman mode.

(b) If the condition differs from the previ-

ous one, the radar sounds an audible

alarm, cancels the watchman mode

and transmits continuously.

7. To cancel the watchman mode manually,

press any key.

2.26 Plotting

This function plots the movement of other

ships relative to your own ship.

Press the [PLOT (A/C RAIN)] control to start

plotting. The indication “PLOT” and a timer

appear at the top right-hand corner of the

screen and movement of all targets is plot-

ted. The timer counts up from 0:01 to 99:59,

whereupon the timer indication freezes but

plotting continues. Targets initially are up-

dated every 15 seconds. However, you can

select intervals of 30 seconds, 1 minute, 3

minutes or 6 minutes through the MENU dis-

play (Refer to Chapter 3). The plotting inter-

val (except for 15 seconds) appears to the

right of the indication PLOT.

If the range is changed during plotting, plot-

ting begins anew with the newly selected

range. To cancel plotting, press the [PLOT]

key.

0:25

PLOT

18:25

PLOT 3M

Timer

Plotting Interval

(30 sec., 1min.,3min., 6min.)

Figure 2-14 Plotting Indications

Plot Brilliance

The brilliance of plotted echoes is selectable

through the MENU display. Press the [MENU]

key and select “5. PLOT BRILLIANCE”.

2.27 Navigation Data Display

Navigation data can be displayed on the

screen if your radar receives navigation in-

put form a Loran-C, NNSS (satellite naviga-

tor) or GPS navigator whose output formats

is IEC 61162 or FURUNO CIF. Data

displayable include own ship’s position in lati-

tude and longitude (or Loran-C time differ-

ences (TDs)), bearing and range to a

waypoint selected on the nav aid, own ship’s

speed, heading and course, In addition, if a

heading sensor or gyrocompass is also con-

nected, a line connects a waypoint (selected

on navaid), denoted by a dashed ring, with

the own ship’s position.

To return the navigation data display on or

off, press the [MENU] key and select “8. NAV

DATA”.

To display TDs instead of L/L, press the

[GAIN] control. Press the control again to

restore L/L.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Furuno 1761MK3 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info