Bedienungsanleitung Furuno 1832 (Seite 41 von 63) (Englisch)

28260

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

6.2 Display Unit Installation

Mounting considerations

When selecting a mounting location for the

display unit keep in mind the following points.

¡ Even though the display unit is waterproof,

it is recommended that the display unit

must be mounted inside an enclosed cabi-

net.

¡ Provide adequate space behind and around

the unit to permit circulation of air and to

provide convenient access to the rear con-

nectors.

¡ Even though the picture is quite legible

even in bright sunlight, keep the display

unit out of direct sunlight or at least shaded

because of heat that can build up inside the

cabinet.

¡ Locate the display unit in a position where

you can view and operate it conveniently

but where there is no danger of salt or fresh

water spray or immersion.

¡ The orientation of the display unit should

be so the radar screen is viewed while the

operator is facing in the direction of the

bow. This makes determination of your

position much easier.

¡ Make sure you allow enough clearance

both to get to the connectors behind the unit

and to allow you to get your hands in on

both sides to loosen or tighten the mount-

ing knobs. Make sure you leave at least a

foot or so of “service loop” of cables be-

hind the unit so it can be pulled forward

for servicing or easy removal of the con-

nectors.

¡ The compass safe distance of 0.8 meters

(standard compass) and 0.6 meters (steer-

ing compass) should be observed to pre-

vent deviation of the magnetic compass.

¡ Even though the display unit meets water-

proof standard IPX-5, the connection of ex-

ternal buzzer, radar plotter and/or remote

display can affect waterproofness. Water-

tight integrity cannot be guaranteed. When

these modification has been done, the dis-

play unit should not be mounted where ex-

posed.

Mounting

The display unit is designed to be mounted

on a tabletop or bulkhead.

1. Using the hangar as a template, mark screw

locations in the mounting location.

2. Fix the hanger to the mounting location

with five M6 tapping screws (supplied).

3. Fit the knob bolts to the display unit. In-

stall the display unit in the hunger. Tighten

the knob bolts securely.

Connections

1. Connect the power cable to the power cable

connector on the rear of the display unit.

2. Connect the signal cable to connector DJ-

1 on the rear of the display unit.

3. Run a ground wire (local supply) between

the ground terminal on the rear of the dis-

play unit and the ship’s superstructure.

Navigation aid, video sounder con-

nection

If your navigation aid can output data in

IEC1162(NMEA 0183) data format, your

vessel's position in latitude and longitude, the

range and bearing to waypoint, speed and

course may be input to this radar, and be seen

on the screen.

Further if your video sounder can output depth

in IEC1162 (NMEA 0183) data format, depth

can be displayed on the radar screen.

You will need an NMEA cable:

Type Code no. Remarks

MJ-A6SPF0012-050 000-134-424 6P-6P (5m)

MJ-A6SPF0012-100 000-133-817 6P-6P (10m)

MJ-A6SPF0003-050 000-117-603 w/connector

MJ-A6SPF0009-100 000-125-236 w/connector

This radar can output NAV data received from

a navaid to an echosounder.

1832/1932/1942

SPU9211

J1352 (NMEA)

J1354

Navaid

Echo-

sounder

INT9213

(TLL)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Furuno 1832 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Furuno 1832

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info