Bedienungsanleitung Furuno 1932 (Seite 44 von 63) (Englisch)

28270

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

¡. Nav Talker

2 . Depth Unit

3 . Temp Unit

4 . Hdg Sensor

5 . Key Beep

6 . Ant on Tx

7 . Dead Sector

8 . Tuned/Video

9 . Heading Alignment

10. Sweep Timing

11. MBS Adjustment

12. Ant Height

13. STC Curve

14. Ope Mode

15. Hours in Use

16. Tx Hours

Low

Mid

Hig

GPS

˚F

Gyro

Stop

Std

Slave

All

˚C

Magnet

Off

Rotate

180˚~180˚

Sharp

Master

000001.5H

000000.0H

Gntl

[ Installation Setup ]

Select item by omnipad

and ress ENTER key.

Auto Adjustment

Adjustment

Figure 6-21 Installation setup menu

Adjusting tune/video

Do the following to adjust tune and video am-

plifier level input.

1. Press the [ST BY/TX] key to transmit.

WARNING

Before transmitting the radar make sure

no one is near the antenna unit, to pre-

vent the potential risk of being struck

by the rotating antenna and exposure

to RF radiation hazard.

2. On the Installation setup menu, select “8.

Tune/Video Adjustment” and press the

[ACQ/ENTER] key.

3. The unit automatically adjusts, displaying

the following message.

[ Tune/Video Auto Adjustment ]

Now under correction.

Return to illustration setup.

menu after the correction.

Figure 6-22 Tune/Video Auto

Adjustment messages

4. When adjustment is completed, the mes-

sages disappears.

Entering antenna height

The STC curve changes with respect to an-

tenna height above the waterline. Enter an-

tenna height above the waterline to optimize

the STC curve.

1. Select “12. Antenna Height” on the instal-

lation setup menu and press the [ACQ/EN-

TER] key.

2. Operate the omnipad to select antenna

height above the waterline; Low (~3 m),

Mid (3~6 m) or High (6~10 m).

3. Press the [ACQ/ENTER] key.

Aligning heading

(Adjustment sector:0~359.90)

You have mounted the antenna unit facing

straight ahead in the direction of the bow.

Therefore, a small but conspicuous target dead

ahead visually should appear on the heading

line (zero degrees).

In practice, you will probably observe some

small error on the display because of the dif-

ficulty in achieving accurate initial position-

ing of the antenna unit. The following

adjustment will compensate for this error.

1. Identify a suitable target (for example, ship

or buoy) at a range between 0.125 to 0.25

nautical miles, preferably near the head-

ing mark. To lessen error, keep echoes in

the outer half of the picture by changing

the range. Also, be sure the zoom and off

center functions are off.

2. Select “9. Heading Alignment” on the in-

stallation setup menu and press the [ACQ/

ENTER] key. The following message ap-

pears on the display.

[ Heading alignment ]

Set EBL1 to center of target

dead ahead and press ENTER.

Correction 0.0°

Figure 6-23 Heading alignment message

3. Operate the omnipad to bisect target se-

lected at step 1 with the heading line.

4. Press the [ACQ/ENTER] key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Furuno 1932 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Furuno 1932

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info