Bedienungsanleitung Furuno 1932 (Seite 51 von 63) (Englisch)

28270

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

AP-5

LARGE CIRCLE

The plot symbol of a target under tracking

becomes twice as large as the normal symbol

when the target is selected for data reading.

Note 1:The target to be acquired should be

within 0.2 to 16 nm from own ship and not

obscured by sea or rain clutter for successful

acquisition.

Note 2:When you want to acquire 11th target,

cancel tracking one of less important targets.

Note 3:When auto acquisition mode (Auto

ACQ) is on, up to 5 targets can be acquired.

For detail, see next section titled Automatic

Acquisition.

WARNING

When a tracked target nears another

tracked target, the targets may be

"swapped." When two targets come close

to each other, one of the two can become

a "lost target." Should this happen,

reacquisition of the "lost target" is required

after the two targets have separated.

Automatic Acquisition

The Auto plotter ARP-10 can acquire up to 5

targets automatically by setting the Auto Ac-

quisition area predefined in the system. If Auto

ACQ is selected after more than 5 targets have

been manually acquired, only the remaining

capacity of targets can be automatically ac-

quired. Example; when 7 targets acquired

manually, then the Auto ACQ is switched on

only 3 targets can be acquire automatically.

When five targets have been automatically

acquired, "AUTO TARGET FULL" message

appears at top left corner on the display.

Setting Auto Acquisition Area

Auto acquisition area is predefined between

2.0 and 2.5 nm in range and 45º on either side

of the heading line in bearing. If a target come

into this area, it is acquired automatically.

Deactivating the Auto Plotter

To deactivate the Auto Plotter,

1. Open the "ARP-10 MENU".

2. Operate the omnipad to select the "1. Dis-

play".

5. Operate the omnipad to select "Off".

6. Press the [ACQ/ENTER] key.

7. Press the [MENU] key to close the menu.

Acquiring targets

Manual Acquisition

Follow the steps below to manually acquire a

target. Up to 10 targets can be manually ac-

quired.

1. Place the cursor (+) on a target of interest

by operating the omnipad.

2. Press the [ACQ/ENTER] key.

The plot symbol changes its shape according

to the status as below. A vector appears in

about one minute after acquisition indicating

the target's motion trend. If the target is con-

sistently detected for three minutes, the plot

symbol changes to a solid mark. If acquisi-

tion fails, the target symbol blinks and disap-

pears shortly.

SQUARE (dotted)

Immediately after acquisition - Plot symbol

shown in broken lines.

SQUARE (dotted with a vector)

One minute after acquisition - Vector still un-

reliable.

CIRCLE (Solid with a vector)

3 minutes after acquisition - Plot symbol

changes to a solid circle indicating the stable

tracking condition.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Furuno 1932 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Furuno 1932

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info