689491
15
Zoom out
Zoom in
Vorherige Seite
1/125
Nächste Seite
-1.1-
1 OPERATIONAL OVERVIEW
1.1 Turning on the Power
The [POWER] switch is located at the left corner of the display unit. Push it to switch on the radar
set. To turn off the radar, push it again. The screen shows the bearing scale and digital timer
approximately 15 seconds after power-on. The timer counts down three minutes of warm-up time.
During this period the magnetron, that is, the transmitter tube, is warmed for transmission. When
the timer has reached 0:00, the indication STBY appears, indicating that the radar is now ready to
transmit pulses.
Switch S2
Notice for technicians
The display unit designed to run on AC voltage
has a switch (S2) at its rear to cut off 115/230 V
supply from internal circuits. Thus, the radar will
not operate when this switch is turned off. Keep it
in the ON position.
1.2 Transmitter ON
After the power is turned on and the magnetron has warmed up, STBY appears at the screen
center, indicating the radar is ready to transmit radar pulses. Press the [STBY/TX] key to transmit.
When you won’t be using the radar for an extended period, but you want to keep it in a state of
readiness, place it in standby by pressing the [STBY/TX] key. The display shows STBY.
Video Freeze-up Recovery
Video freeze-up or lock-up can occur unexpectedly on any digital rasterscan radars. This is
mainly caused by heavy spike noise in the power line and can be noticed by carefully watching
the nearly visible sweep line. If you suspect that the picture is not updated every scan of the
antenna or no key entry is accepted notwithstanding the apparently normal pictures, do Quick
Start to restore normal operation.
.1 Turn off the Power Switch and within 10 seconds turn it on again.
.2 Press the Transmit switch labeled STBY/TX for transmit condition.
POWER
switch
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Furuno FR1510 MARK-3 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Furuno FR1510 MARK-3

Furuno FR1510 MARK-3 Installationsanweisung - Englisch - 75 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info