612626
16
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
1-10
1.9 Displaying Station Name
User channels 0-01 to 0-65 can be registered with a name, and it or the Rx frequency can be
displayed on the second line of the display. This function is available when a system setting is
set to display both channel and frequency. See page 3-3 for how to register station name.
1. Press [ENT] and [CURS/2] keys together. Each time those keys are pressed together, Rx
frequency or station name is displayed on the second line of the display.
2. When station name is displayed, you may press the [ENT] key to display Tx and Rx fre-
quency temporarily.
02
4
R
6810
S
TLX
AGC
DUP
Station
Press ENT + CURS
R
02
4
6810
S
TLX
AGC
DUP
RX freq
Note: If no station name is registered,
Rx frequency is soon displayed.
CH No. (Example)
Figure 1-8 How to display Rx frequency and station name alternately
1.10 Transmitting
After selecting class of emission and frequency, you can transmit by pressing the PTT (press-
to-talk) switch on the microphone (handset). (“T” appears when the PTT switch is pressed.
Output power can be evaluated on the operation display. Do not transmit any signal other than
emergency during the silence period, 00 to 03 min, and 30 to 33 min of every hour.
Tuning the antenna
Maximum transmission power is achieved only when the antenna impedance and transmitter
impedance match each other. Because the antenna impedance changes with frequency a means
must be provided to match (tune) the antenna impedance with the transmitter impedance. This
is done with the antenna coupler. The antenna coupler automatically tunes the transmitter to a
wide range of different antenna length (6 – 15 m). To initiate the automatic tuning, do the
following:
1. Press the PTT switch on the microphone (handset), or the [TUNE/7] key.
2. “TUNE” appears on the display.
3. Tuning will be completed within 2 to 15 seconds for a newly selected frequency, or less than
0.5 seconds for a once tuned frequency. (A built-in memory remembers coil and capacitor
settings.)
4. When the tuning process is successfully completed “OK” appears.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Furuno FS-1503 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info