Bedienungsanleitung Furuno GP-1650WF (Seite 76 von 113) (Englisch)

522154

Zoom out

Zoom in

Vorherige Seite

1/113

Nächste Seite

offered by Busse-Yachtshop.com

11. CUSTOMIZING YOUR UNIT

11-6

1. Select GEODETIC DATUM.

2. Press the EDIT soft key to show the

geodetic datum window.

GEODETIC DATUM

CHART DATUM

▲

AUSTRALIA

▼

WGS-84

Geodetic datum window

3. Press ▲ or ▼ to select the chart system

you are using. If UNKNOWN appears in

the GEODETIC DATUM window, select a

different chart system to show the proper

chart datum.

4. Press the ENTER soft key or the

[ENTER] key to register your selection.

POS SMOOTHING

When the DOP or receiving condition is

unfavorable, the GPS fix may change, even

if the vessel is dead in water. This change

can be reduced by smoothing the raw GPS

fixes. A setting between 000 to 999 is

available. The higher the setting, the more

smoothed the raw data, however too high a

setting slows response time to change in

latitude and longitude. This is especially

noticeable at high ship’s speeds. 000 is the

normal setting; increase the setting if the

GPS fix changes.

SPD/CSE SMOOTHING

During position fixing, ship’s velocity (speed

and course) is directly measured by

receiving GPS satellite signals. The raw

velocity data may change randomly

depending on receiving conditions and other

factors. You can reduce this random

variation by increasing the smoothing. Like

with latitude and longitude smoothing, the

higher the speed and course smoothing the

more smoothed the raw data. If the setting is

too high, however, the response to speed

and course change slows. For no smoothing,

enter all zeroes. The default setting is 005

(sec).

GPS SPEED AVE

Calculation of ETA is based on average

ship’s speed over a given period. If the

period is too long or too short calculation

error will result. Change this setting if

calculation error occurs. The default setting

is 60 seconds, which is suitable for most

conditions.

LAT OFFSET, LON OFFSET

GPS-generated position may be off from the

chart. In this case, you can apply an offset to

GPS position to refine position accuracy.

Mark the equipment indication on the chart,

and then calculate the L/L error.

1. Select LAT OFFSET or LON OFFSET.

2. Press the EDIT soft key.

3. Key in the error value. To switch the

north and south (east and west), press

the N<->S (W<->E) soft key.

4. Press the ENTER soft key or [ENTER]

key.

DISABLE SATELLITE

Every GPS satellite is broadcasting

abnormal satellite number(s) in its Almanac,

which contains general orbital data about all

GPS satellites, including those which are

malfunctioning. Using this information, the

GPS receiver automatically eliminates any

malfunctioning satellite from the GPS

satellite schedule. However, the Almanac

sometimes may not contain this information.

If you hear about a malfunctioning satellite

from another source, you can disable it

manually. Enter satellite number (max. 3

satellites) in two digits and press the ENTER

soft key or the [ENTER] key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Furuno GP-1650WF Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info