522178
10
Zoom out
Zoom in
Vorherige Seite
1/45
Nächste Seite
1. INSTALLATION
4
1.4.2 Deck Mount
See the outline drawing for mounting hole dimensions and fixing instructions
1. Unscrew the mount base (part C) from the surface bracket (part E) (see figure above). Re-
move the label from over the GPS receiver's socket. (The label may be discarded.) Fasten the
mount base (part C) to the GPS receiver (part A) with the supplied panhead screws, flat wash-
ers and spring washers. The torque for the screws is 1.35 N m.
2. Screw the surface bracket (part E) onto the mount base of the assembled GPS receiver. Use
a pencil to extend the alignment tab onto the surface bracket. Unscrew the surface bracket.
3. At the selected location, position the surface bracket with the pencil mark facing forward. Us-
ing it as a template, mark the position for the three mounting screws and the center hole for
the cable.
4. Using a 3 mm or 1/8" bit, drill the pilot holes. Using 5.1 mm or #7 bit, drill the three mounting
holes. Drill the cable hole with a 25 mm or 1" bit.
Fiberglass-Minimize surface cracking by running the drill in reverse until the gelcoat is pen-
etrated.
5. At the location shown in the figure above, coat the surface bracket (part E) with silicone seal-
ant.
6. Apply silicone sealant to the three #10 x 1/2" self-tapping screws to seal the deck. With the
pencil mark facing forward, fasten the surface bracket in place. Do not block the drain slots.
They will allow any water that accumulates inside the surface bracket to escape. CAUTION:
Do not use a liquid thread locker as it may weaken the plastic, causing it to swell and crack.
7. Wrap pipe thread tape around the threads of the mount base two times to seal it tightly to the
surface bracket.
8. Coat the part of the GPS connector shown in the figure on page 4 with silicone sealant. Pass
the GPS connector end of the cable up through the hole in the surface bracket.
9. Remove the protective cap from the cable's GPS connector. (Save the cap to protect the con-
nector, when the receiver is removed.) Plug the cable firmly into the GPS receiver.
10. Counterclockwise twist the cable three and one-half turns. Then screw the GPS receiver onto
the installed surface bracket. Hand-tighten only. Do not over tighten.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Furuno GP-330B wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info