522136
37
Zoom out
Zoom in
Vorherige Seite
1/47
Nächste Seite
30
10. If the bottom is displayed in dark gray
and the depth indication appears, the
mounting location is suitable. Go to
“Final preparation.”
11. If the bottom is not displayed in dark
gray tone, the mounting location may be
unsuitable. Do the following:
a)
Press the [POWER/BRILL] key to
turn off the power.
b)
Gently dismount the transducer with
a piece of wood.
c)
Reattach the transducer elsewhere
as shown in “Attaching the
transducer.”
d)
Check the installation again.
Final preparation
Support the transducer with a piece of
wood to keep it in place while it is drying.
Let the transducer dry 24-72 hours.
4.5 Optional Triducer
525ST-MSD
The optional triducer 525ST-MSD is
designed for thru-hull mounting. For how to
install this transducer see paragraph 4.2.
φ79 mm
1
33 mm
2.00"-12 UN
threads
φ51 mm
27 mm
7 mm
140 mm
Triducer 525ST-MSD
525ST-PWD
The Transom Mount Transducer or
TRIDUCER
®
Multisensor with Integral
Release Bracket 525ST-PWD is
manufactured by AIRMAR Co. These
instructions are included with the sensor.
Pre-test for speed and temperature
Connect the sensor to the instrument and
spin the paddlewheel. Check for a speed
reading and the approximate air
temperature. If there is no reading, return
the sensor to your place of purchase.
Tools and materials needed
Scissors
Masking tape
Safety goggles
Dust mask
Electric drill
Drill bit for:
Bracket holes: 4mm, #23, or 9/64”
Fiberglass hull: chamfer bit (preferred),
6mm, or 1/4”
Transom hole: 19mm or 3/4” (optional)
Cable clamp holes: 3mm or 1/8”
Screwdrivers
Straight edge
Marine sealant
Pencil
Zip-ties
Water-based antifouling paint (mandatory
in salt water).
Mounting location
To ensure the best performance, the sensor
must be submerged in aeration-free and
turbulence-free water. Mount the sensor
close to the centerline of the boat. On
slower heavier displacement hulls,
positioning it farther from the centerline is
acceptable.
Allow adequate space above the bracket
for it to release and rotate the sensor
upward.
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Furuno LS-6100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info