Bedienungsanleitung Fusion Apollo MS-ERX400 (Seite 7 von 12) (Englisch)

740411

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Enabling Standby Mode

By default, when you press , the device turns off, and you must

press to turn it on again.

You can enable standby mode on the device so you can turn it

on using another device on the network instead of pressing .

NOTE: When the device is off, it continues to draw

approximately 7 mA from the battery. When you enable standby

mode, the device draws more current because it is listening for a

power-on signal over the network. When the device is off with

standby mode enabled, it continues to draw approximately

19 mA.

Select > SETTINGS > POWER OPTIONS > STANDBY

MODE.

The device now enters standby mode when you press . You

can turn it on again from the CONTROL screen on any device

on the network.

Turning Off Devices on the Network

You can turn off any device connected to the network using the

remote control.

Hold .

A list of devices connected to the network appears.

Select an action:

• Select a device on the network to turn it off.

• Select SYSTEM OFF to turn off all devices connected to

the network.

Fusion PartyBus Networking

The Fusion PartyBus networking feature allows you to connect

multiple compatible stereos together on a network, using a

combination of wired or wireless connections.

You can group a compatible stereo, such as the Apollo RA670

stereo, with other compatible stereos connected to the network.

Grouped stereos can share available sources and control media

playback on all of the stereos in the group, which allows for a

synchronized audio experience across the vessel. You can

quickly create, edit, and break up groups as needed from any

compatible stereo or remote control on the network.

You can use compatible stereos and remote controls, whether

they are grouped or not, to adjust the volume of the available

speaker zones for any stereo on the network.

You should refer to the installation instructions provided with

your stereo when constructing the Fusion PartyBus network.

Creating a Group

Before you can create a group, you must connect multiple

compatible stereos to the Fusion PartyBus network. See the

installation instructions provided with your stereo for information

about installing and configuring the network.

Press the dial to open the CONTROL screen.

Turn the dial and select EDIT GROUP under the name of the

stereo you want to be the primary stereo in the group.

Select the stereos you want to add to the group.

Select GROUP.

When the stereo is in a group, you can control the volume of all

zones in a group at once from the CONTROL screen. From the

source screen, you can select the source of any stereo in the

group, except the Apollo SRX400 stereo and any sources that

are not enabled on the Fusion PartyBus network.

Editing a Group

Press the dial to open the CONTROL screen.

Turn the dial, and select EDIT GROUP.

Select the devices you want to add to or remove from the

group.

Select GROUP or UNGROUP.

Leaving a Group

You can leave the Fusion PartyBus group to play local sources

on the stereo.

Press the dial to open the CONTROL screen.

Turn the dial, and select EDIT GROUP under the name of the

group that you want to leave.

Select the devices you want to remove from the group.

Select UNGROUP.

Network Source Considerations

When selecting sources to play over the network, you should

observe these considerations.

• A zone stereo, such as the Apollo SRX400, can create or join

a group to control and play sources from other stereos, but it

cannot share its sources with the group.

• You cannot share an AirPlay

source with grouped stereos.

Using AirPlay 2 software, you can play content on multiple

stereos on the network, but the stereos must not be grouped.

• You can disable sharing on most sources by changing the

PARTYBUS ENABLED setting for the source. When

disabled, the source cannot be selected from a grouped

stereo.

• When audio sources are shared over a data network, there is

a slight delay in the synchronized audio that may be

noticeable if you are also using an external audio source.

◦ If you have a television with an Optical Out connection to

the stereo and you continue to use the television

speakers, there will be a delay between the audio from the

television speakers and the optical audio synchronized on

the grouped stereos.

◦ If you synchronize a radio station and tune that same

radio station on a non-networked stereo, there will be a

delay between the audio from the non-networked stereo

and the audio from the radio station synchronized on the

grouped stereos.

◦ You can remove this delay by changing the PARTYBUS

ENABLED setting for the source, but the source cannot be

shared with grouped stereos.

General Settings

Select , select the name of the remote control, and select

SETTINGS.

NOTE: If you select the name of the currently-controlled stereo

before you select SETTINGS, you can adjust the settings of the

stereo instead of the remote control.

The following setting descriptions apply to the remote control

only. For information about stereo-specific settings, see the

stereo owner's manual.

ZONE > ASSIGN HOME ZONE: Assign the default zone on a

connected stereo for the remote control.

BRIGHTNESS: Sets the brightness level on the remote control.

LANGUAGE: Sets the language used on the remote control.

DEVICE NAME: Assigns a name to the remote control for better

identification on the network.

POWER OPTIONS: Sets power options for the remote control

(Power Options, page 4).

NETWORK: Adjusts network settings (Network Settings,

page 4).

Fusion PartyBus Networking 3

Fusion Apollo MS-ERX400 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fusion Apollo MS-ERX400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info