Bedienungsanleitung Fusion Apollo MS-RA670 (Seite 6 von 18) (Englisch)

691367

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Adjust the brightness level.

Enabling Standby Mode

You can set the stereo to enter a low-power standby mode when

you turn off the ignition or hold . When you turn on the ignition

or press again, it takes less than the typical 30 seconds to

turn on.

NOTE: When the stereo is in low-power standby mode, it

continues to draw current from the battery. The maximum

current draw in standby mode is 50 mA.

Select > SETTINGS > POWER OPTIONS > STANDBY

MODE.

The stereo now enters standby mode when you hold .

Audio Control

Adjusting the Volume

Turn the dial to adjust the volume.

If necessary, press the dial to switch between zones.

TIP: To control all zones at the same time, press the dial

repeatedly to select GLOBAL.

Muting all Connected Stereos

You can quickly mute the audio from this stereo or from all

stereos connected to the network (FUSION PartyBus

Networking, page 8).

From any source, select .

The mute symbol appears and audio from this stereo is

silenced.

Press and hold the dial to select MUTE SYSTEM.

Audio from all connected stereos is silenced.

Press the dial to select UNMUTE SYSTEM.

Audio is restored to all connected stereos.

Adjusting the Tones

Select > SETTINGS > ZONE.

Select a zone.

Select TONE.

Select an option:

• Use the slider bar to adjust the level of each tone.

• Press the dial to select a tone, and turn the dial to adjust

the level for the tone.

Disabling the Loud Setting for a Zone

The LOUD setting maintains frequency response at low volumes

and increases perceived loudness at high volumes. This setting

is enabled by default in all zones.

Select > SETTINGS > ZONE.

Select a zone.

Select LOUD to clear the check box.

Adjusting the Gain for an Auxiliary Device

You can adjust the gain for a connected auxiliary device to

achieve a volume level similar to that of other media sources.

You can adjust the gain in 1 dB increments. You can also adjust

the gain for digital sources using an optical audio connection.

Select an auxiliary source.

Select an option:

• To increase the gain, select .

• To decrease the gain, select .

NOTE: To achieve the best audio quality when using a

portable media player with headphone output, it may be

necessary to adjust the volume control on the media player,

instead of adjusting the gain.

Synchronizing the Source and Zone Volume

Levels

You can synchronize the volume levels on one or all zones with

some source devices, such as a Bluetooth source.

Select > SETTINGS > ZONE > PHONE VOLUME ZONE

SYNC.

Select a zone or GLOBAL.

When you adjust the volume on the source device, the volume

on the selected zone is also adjusted.

Speaker Zones

You can group speakers in one area into a speaker zone. This

enables you to control the audio level of the zones individually.

For example, you could make the audio quieter in the cabin and

louder on deck.

You can set the balance, volume limit, tone, subwoofer level,

subwoofer frequency, and name for each zone, and configure

other zone-specific settings (Speaker Zone Settings, page 9).

Adjusting Additional Audio Settings for a Zone

Select > SETTINGS > ZONE.

Select a zone.

Select MORE.

Select one or more options:

NOTE: Not all options are available for all zones.

• To limit the maximum volume output of this zone, select

VOLUME LIMIT, and adjust the level.

• To set the subwoofer level for this zone, select SUB

LEVEL, and adjust the level.

• To adjust the right and left speaker balance of this zone,

select BALANCE, and adjust the balance.

Adjusting the Subwoofer Filter

You can use the subwoofer filter setting to control the subwoofer

cutoff frequency for each zone, which can enhance the blend of

the sound produced by the speakers and the subwoofer. Audio

signals above the selected frequency are not passed to the

subwoofer.

NOTE: If a DSP setting has been applied to zone, this setting

cannot be changed on the stereo. You can view the DSP setting

for the optimal cutoff frequency as calculated by the DSP

controller, but cannot adjust it.

Select > SETTINGS > ZONE.

Select a zone.

Select SUB FREQ.

Select a frequency.

DSP Settings

This stereo features digital signal processing (DSP). You can

select pre-configured DSP settings for FUSION

speakers and

amplifiers to optimize audio reproduction in their installed

locations.

All DSP settings are configured using the FUSION-Link

™

remote

control app (FUSION-Link Wireless Remote Control App,

page 10).

Configuring the DSP Settings

You must download and install the FUSION-Link remote control

app on your compatible Apple

or Android

™

device before you

can configure the DSP settings (FUSION-Link Wireless Remote

Control App, page 10).

2 Audio Control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fusion Apollo MS-RA670 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fusion Apollo MS-RA670

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info