Bedienungsanleitung Futaba 12Z (Seite 23 von 127) (Englisch)

29029

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

How to turn ON/OFF the power of the

transmitter

For safety reasons, the radio will be emmiting

only after confirming when turning on the power.

Please follow the instructions for turning on/off the

transmitter.

When turning on the power of the transmitter

1. Turn on the power switch of the transmitter.

*After initialization of the transmitter is over, the frequency

confirmation screen pops up, and LED monitor turns on

pink.

2. Check the frequency shown on the screen. If

it is OK, then select [YES] and push the enter

button.

*LED monitor turns to green and the transmitter begins to

emit radio waves.

*To not transmit, select [NO] and push enter button.

Then, you will see the home screen and you

will be able to set conditions.

How to stop the transmitter

Turn off the power switch of the transmitter. The

internal circuit of the transmitter starts the shut

down process including saving the set-up data. The

LED will blink yellow while the transmitter is in

the shutdown process.

Warning

Once you turn off the power, never operate the

power switch until the power shutdown process

is fully completed. If you turn on the power

switch again while the transmitter is still in the

process of power shutdown, the transmitter

power does not start.

How to change the frequency/How to set ID

The T12Z system has employed the frequency

synthesizer scheme. The T12Z transmitter will set

the frequency of the R5014DPS (PCMG3 receiver)

by the wireless data transmission. When you are

using a new PCMG3 receiver and changing the

frequency, set ID or frequency using the following

instructions.

In case of using PCMG3 receivers

*Make sure that PCM-G3 is set as a modulation scheme.

Then change the frequency by the following instruction.

How to change the frequency

7XUQRQWKHWUDQVPLWWHUSRZHU$FRQÀUPDWLRQ

message ("TRANSMIT?") is displayed. Since

you do not want to transmit, select [NO] and

then push the enter button.

2. Select the area that displays the frequency

on the home screen or in the linkage menu

and push the enter button.

*The frequency setup screen appears.

﷈ﶰ﷊ﶲﶪ﷊ﶸ﷎ﶢ

ﴶﴸﴸﳜ

﷐﷒ﶸ﷌ﵺﶸﶶﵾﶈ﷈ﶰ﷊ﶲﵾ﷎ﷄﶆﶞ

ﻚｄＸﻚﻨＸｂﻞｄ｀ｆ：Ｄ＀ﻦ

Ｘｂ：Ｄ＀

ﶺﶶ﷌ﶪﶼ﷒ﶬﷂﶶﶸﵺﵺﵺﵺﵺﵺﵺﶞ

ﶰ﷊﷎﷊ﷂﶨ﷊ﶰﵺﷂ﷌ﵺﵺﵺﵺﵺﵺﶞ

﷈ﶰ﷊ﶲﵾ﷐﷒ﶸ﷌ﶞﵼﵺ﷒ﶰ﷊﷒ﵺﶞ

﷢ﶸ﷌ﵺﶰ﷊﷎﷊ﷂﶨ﷊ﶰﵺﷂ﷌ﵺﵺﶞ

＠Ｒ４Ｒ８

４Ｎ：ﻚＦ｀

ｆｆｆｆｄｆｆｄ

８６ﻚ＊．Ｊ

ﶺﶶ﷌﷊ﶼ﷤

﷎ﶶﶸ﷌ﷂﶬ﷤

ﴶﴸﳰﴶﴸﳰﴸﴸ

3. Select [RECEIVER ID] and push the enter

button.

*The receiver ID code input screen appears.

4. Input the 8-digit ID code stuck to the receiver

case. If the inputted ID code is correct, select

[ENTER] and then push the enter button.

6HOHFWWKH¿JXUHZLWKWKHFXUVRUNH\DQGSXVKWKHHQWHUNH\

for each digit.

*Use [BACK SPACE] to move back digit by digit for

correction if you made a mistake. When you want to stop

ID code change, push the return key to return to the original

screen.

*Once the receiver ID code is set, it does not have to be reset

as long as the receiver is not changed.

*When you use two receivers with a large aircraft, input the

ID of each receiver.

5. When switching the frequency, select [BAND

NO.] and push the enter button.

*The frequencies which can be selected appear on the screen.

6. Select the frequency you want to use and

push the enter button.

$FRQ¿UPDWLRQPHVVDJHDSSHDUV

*When changing the frequency band, change the module

before turning on the power.

7. If the frequency is correct, push the enter

button.

*A screen which shows that frequency data is being sent

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 12Z Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info